OdysseyGPT

Wind tower and renewable structure fabricators

Wind tower fabrication quality documentation: from the OEM's fabrication specification to the section dossier

For bid, project and quality engineers at fabricators of wind turbine tower sections, foundations and other large welded structures built to an OEM's or developer's specification.

By Ademola Afolabi, Founder, New Odyssey Ltd ยท Last reviewed:

The short answer

Tower fabricators answer a turbine maker's enquiry by reading its fabrication specification and drawings against their own shop practice: plate and flange supply, welding, NDE, tolerances, coating and internals. Each tower section then leaves with its own dossier: certificates with traceability, a weld map and welder records, NDE reports, dimensional and flange flatness reports, and coating inspection records.

Key Takeaways

  • The tower design belongs to the turbine maker and sits inside a certified turbine design. The fabricator builds to it and does not vary it alone.
  • The dossier is per section. The same record set is repeated for every serial number in the order.
  • Flange supply, flange flatness after welding and the coating system are where tower enquiries differ most from general steelwork.
  • OdysseyGPT checks the documents against the specification. It does not read drawings or measure a flange.

Free sample: a certificate check report. Send up to 20 material certificates and the PO. Get a certificate check report. Get the free result

How do tower fabricators answer an OEM's enquiry?

A tower order is serial work. The turbine maker, the OEM, owns the design and issues the same package to each approved fabricator: drawings for every section and a set of specifications that say how to build them. The fabricator is asked for a price per tower and for a statement of where its shop cannot follow the package as written.

What a tower enquiry package usually holds, and the point to settle on each part
Part of the packageWhat it coversPoint to settle before the offer
Fabrication specification and drawingsShell courses, flanges, door frame, weld details and the standards that governWhich document wins when the drawing and the specification disagree?
Plate specificationSteel grade, delivery condition, testing, certificate type and sometimes approved millsCan your plate supplier meet it, and is the mill on the OEM's list?
Flange specificationForged ring flanges: material, testing, machining and certificate typeIs the forge approved by the OEM, and who buys the flanges, you or the OEM?
Welding requirementsProcesses allowed, procedure and welder qualification, and any production testsDo your procedures cover the thickest shell-to-flange joint in the tower?
NDE requirementsMethods and extent for longitudinal seams, circumferential seams and attachments, and the personnel schemeIs the extent for each weld category clear from the package?
TolerancesShell roundness and straightness, section length, and flange flatness and tilt, named here without valuesCan your measuring method and equipment show each one, at the stage the OEM wants it measured?
Surface treatmentBlast cleaning, the coating system inside and outside, inspection and repairIs the named system and paint supplier one you are set up to apply?
InternalsPlatforms, ladders, cable supports and brackets, and what is welded to the shellWhich internals are in your scope, and which welds to the shell need the OEM's approval?
Quality and documentation requirementsThe inspection plan, hold points, audits by the OEM and the record set for each sectionWhat goes in the dossier, in what format, and when is it due?

General points about a steel enquiry, such as the execution class and certificate types, are on the steel fabricators page. What is particular here is that almost nothing is left to the fabricator's choice. The design has been analysed for fatigue by someone else. A change to a weld detail or a bracket position that looks harmless in the shop may not be harmless to that analysis, so it goes back to the OEM as a deviation request.

Which standards come up in tower fabrication?

Standards often named in tower and support structure enquiries (own summary at name level; use the edition your contract names)
StandardWhat it isHow it reaches the fabricator
EN 1090-2Technical requirements for the execution of steel structuresEuropean OEM specifications commonly build on it and state the execution class
ISO 3834Quality requirements for fusion welding of metallic materialsThe welding quality system the shop is expected to run and often to hold certification for
EN 10204Types of inspection document for metallic productsThe specification states type 3.1 or 3.2 for plate and for flanges, and they are not always the same
ISO 12944Corrosion protection of steel structures by protective paint systems, in several parts including one for offshore structuresCalled up for the coating system, or replaced by the OEM's own coating specification
IEC 61400 seriesThe international standards for wind energy generation systems, including design requirements for turbines, towers and foundationsContext only. The OEM designs to it. The fabricator sees its effect through the OEM's specification
DNV-ST-0126DNV's standard, Support structures for wind turbinesDNV describes it as a contractual reference for the design and construction of support structures. Some specifications name it
The OEM's specificationsThe turbine maker's own documents for fabrication, welding, coating and qualityThey govern. Where they are stricter than a standard, the stricter rule is the contract

The turbine itself is usually covered by a type certificate, and the tower design is part of what was assessed. That is the reason an OEM controls its fabrication specification so closely. Welding codes from other families appear on some projects. For the American structural code, see AWS D1.1. These are paid documents and this page does not give their limits.

What goes in a tower fabricator's deviation list?

There are two kinds of deviation in tower work. The first is raised with the offer: a standing difference between the OEM's package and how your shop works. The second is raised during production against one section, often called a concession or a non-conformance request. Both need the OEM's written answer. Typical subjects are these.

  • Plate supply: a mill that is not on the OEM's approved list, a different delivery condition, or a plate size that moves the position of a seam.
  • Flanges: an alternative forge, a certificate type other than the one specified, or a machining sequence that differs from the specification.
  • Welding: a process or consumable the specification does not list, or a joint preparation changed to suit your equipment.
  • Seam layout: a different number of shell courses or a changed offset between longitudinal seams, which alters the weld map.
  • NDE: a method substituted for the one named, or a different personnel certification scheme.
  • Tolerances: the stage at which flange flatness is measured, or the measuring method, where yours differs from the OEM's.
  • Coating: an equivalent paint system from another supplier, or application conditions your booth cannot hold all year.
  • Internals: brackets welded where the drawing shows bolted or magnetic fixings, or the reverse.
  • Records: your own report formats where the OEM issues templates, or a different dossier structure.

Write each row with the clause, your proposal and the reason. The technical deviation list guide shows the layout. The Deviation Register (beta) then keeps the OEM's answers in one list, which matters when the same answer has to hold for every section in a long series.

Which documents go with each tower section?

The record set for one tower section, and the gap that most often holds a section back
RecordWhat it showsGap that holds a section
Plate certificates with traceabilityEach shell course tied to a plate, a heat and a certificate of the type specifiedA course whose plate number was not carried from the cutting record to the section's material list. See heat number traceability
Flange certificatesMaterial tests, any examination by the forge and the dimensional record for each flange, by serial numberA certificate of the wrong type, or one whose serial number is not the flange welded on
Weld map and welder recordsEvery longitudinal seam, circumferential seam and attachment weld, with its procedure, welder and dateAttachment welds for internals left off the map
NDE reportsExamination of each weld to the method and extent specifiedA seam on the map with no ultrasonic report, or a repair with no later report
Heat treatment recordsPost-weld heat treatment charts, only where the specification asks for itNot applicable on most sections. A gap only when the clause exists and the chart does not
Dimensional reportLength, roundness and straightness of the section against the drawing tolerancesReadings taken before the last weld was made
Flange flatness reportFlatness and tilt of each flange after welding, with the method and instrumentA report with no instrument identity, or measured at a different stage from the one specified
Coating inspection recordsSurface preparation, conditions, each coat applied and film thickness checks, inside and outsideA record for one coat of the system missing from the set
Section dossierAll of the above for one serial number, in the OEM's index orderA dossier assembled from the previous section's template with the old serial number left in

The wind tower section ITP template sets out the inspection stages these records come from. Because every section has the same index, a gap tends to repeat. If the intermediate coat record is missing from one dossier, check the other sections coated in the same week.

How does OdysseyGPT help?

OdysseyGPT takes the OEM's requirements and your documents and reports where they differ, with the passage quoted from each. A quality engineer accepts or rejects every finding. It reads text and tables, so the weld map and the material list must be given as a list or spreadsheet. A drawing alone will not do.

Tower documents and the OEM requirement each OdysseyGPT tool checks them against
Your documentsChecked againstToolWhat is reported
Your quality plan and standard proceduresThe OEM's fabrication, welding and coating specificationsDocument ReviewRequirements your documents meet, differ from or do not mention, as a draft deviation list
The OEM package on its ownNothing else: it is read aloneCustomer Specification Review (beta)The requirements listed by type, with open items such as a specification named and not supplied
Your inspection and test planThe OEM's quality requirementsITP Validator (beta)Missing stages, and hold or witness points entered at a lower level
Plate and flange certificatesThe purchase requirementsMaterial Certificate Review (beta)Wrong certificate type, wrong grade or condition, and required tests the certificate does not report
The section's material list and heat registerThe certificates on fileMaterial Traceability Check (beta)Heats with no certificate and certificates tied to no part
Welder qualifications and the weld logYour welding procedures and their qualification recordsWelding Qualification Review (beta)Welds outside the qualified range and welders not qualified on the weld date
NDE reports and repair recordsThe weld map and the specified method for each weldNDE Coverage Review (beta)Welds with no report, a different method, short coverage or an unclosed repair
Inspection reports that name an instrumentThe calibration certificatesCalibration Validity Check (beta)Instruments with no certificate, or one that was out of date when the reading was taken
The section's document folderThe OEM's dossier indexMRB Readiness Check (beta)Index lines with no document, old revisions and unapproved records
The compiled dossierThe weld map and ITPMRB Traceability Verification (beta)Broken links from weld to welder and procedure, and from shell course to heat and certificate

No tool judges the numbers on a flatness, dimensional or coating report. The checks above confirm that those reports exist for the section, carry the right serial number and name an instrument that was in calibration. The MRB Compiler (beta) lays the approved documents out against the OEM's index for the final dossier.

What does a result look like for a tower section?

Everything in this example is invented: the section, the weld numbers, the flange serial number, the heat number, the instrument and the dates. No real project or supplier is behind it. It is here to show the form of the findings.

Invented example: the dossier for one tower section (T2, the second section from the base) checked against the turbine maker's fabrication specification
IDFindingWhy it was raisedCategorySeverityConfidence
F-MTR-01Top flange certificate is EN 10204 type 3.1 where type 3.2 is requiredThe flange specification asks for a type 3.2 inspection certificate for all ring flanges. The certificate for flange serial FL-2291 is headed 3.1 and carries no independent inspector's endorsement.Certificate typeCriticalHigh
F-MTR-02Plate certificate does not report the through-thickness test the order requiresThe plate purchase requirement lists a through-thickness tensile test for the shell course welded to the flange. The certificate for plate P-0417 shows tensile and impact results only.Missing testHighHigh
F-TRC-01Heat 73L208 on shell course 5 has no certificate in the setThe section material list records heat 73L208 for course 5. No plate certificate in the folder carries that heat number.Unlinked heatHighHigh
F-NDE-01Circumferential weld CW-06 has no ultrasonic reportThe weld map lists CW-06 between courses 6 and 7. The specification requires ultrasonic examination of every circumferential seam. The reports cover CW-01 to CW-05 and CW-07.Missing reportCriticalHigh
F-NDE-02Repair on longitudinal weld LW-03 was not examined againRepair record R-014 for LW-03 is dated 2026-03-11. The only ultrasonic report that names LW-03 is dated 2026-03-09.Unclosed repairHighMedium
F-WLD-01Welder W-41 was not qualified for the process used on the door frame weldThe weld log records submerged arc welding by W-41 on DF-01. The welder's certificate on file covers a different process.Welder qualificationCriticalHigh
F-ITP-01ITP shows flange flatness measurement after welding as a review pointThe quality requirements make flange flatness measurement after welding a hold point for the purchaser's inspector. ITP line 14 marks it R.Downgraded inspection pointMediumHigh
F-CAL-01Film thickness gauge on the coating record was out of calibration on the date of useCoating inspection record CIR-T2-03 names gauge DFT-07 on 2026-03-20. The calibration certificate for DFT-07 expired on 2026-02-28.Expired at useHighHigh
F-MRB-01No inspection record for the intermediate coatThe dossier index lists three coating inspection records for the outside surface: primer, intermediate coat and top coat. The folder holds records for the primer and the top coat.Missing documentHighHigh

Each finding opens to the document, the page or cell and the quoted text. Several of these would be settled by finding a misfiled report. One or two would hold the section. The engineer makes that call, and the list makes sure the question is asked before the OEM's inspector asks it.

Where OdysseyGPT falls short

  • It does not read tower drawings or models. Seam numbers, course numbers and flange serial numbers have to come from a list.
  • It does no structural or fatigue assessment and cannot say whether a deviation is acceptable to the tower design. That is the OEM's decision.
  • It does not measure anything. It does not perform or assess a flange flatness survey, a dimensional survey or a film thickness check, and it does not judge the readings on those reports.
  • It does not interpret ultrasonic data. It reads the result the technician wrote on the report.
  • It does not certify a section, a weld, a welding quality system or a fabricator, and it has no role in turbine type certification.
  • It is not production software. It does not plan the rolling line, track sections through the shop or manage plate stock.
  • It checks against the documents you give it. If the OEM's coating specification is not uploaded, coating clauses cannot be checked.
  • To judge it, take the dossier of a section that was held at final inspection and see whether the review finds the reason.

Which tools are available now

Document Review is generally available. Every other tool on this page is in beta, which means you request access and we onboard your team ourselves. See the inspection module, the handover module and OdysseyGPT for manufacturing.

Try it on your own documents

Free sample: a certificate check report

Send up to 20 material certificates and the PO. Get a certificate check report.

Get the free result

Buyer questions

20 questions bid engineers, proposal engineers and buyers ask. Last reviewed:

What quality documentation does wind tower fabrication need?

Each tower section needs its own record set. It normally holds plate and flange certificates with traceability, a weld map with welder and procedure records, NDE reports, a dimensional report, a flange flatness report for each flange and coating inspection records. The turbine maker's documentation clause gives the exact list, the report formats and the index for the section dossier.

What is in a wind turbine tower fabrication specification?

It is the turbine maker's set of rules for building its tower. It covers plate and flange materials, welding processes and qualification, NDE methods and extent, tolerances for the shell and flanges, the coating system, internals and the quality records required. It usually builds on public standards and adds stricter project rules. Read it with the drawings, since each refers to the other.

Who is responsible for the tower design?

The turbine maker, or the developer's designer for some foundations. The fabricator builds to the drawings and specification and is responsible for workmanship and records. That split matters for deviations: a fabricator cannot judge whether a changed weld detail is acceptable, because the fatigue assessment behind the design is not theirs. Every such change goes to the designer for a written answer.

Which standards apply to wind tower fabrication?

The turbine maker's specification governs. European specifications commonly call up EN 1090-2 for execution, ISO 3834 for welding quality, EN 10204 for inspection documents and ISO 12944 or the maker's own document for coating. The IEC 61400 series governs the turbine design and reaches the shop only through the specification.

Does IEC 61400 apply to a tower fabricator?

Not directly in most contracts. IEC 61400 sets design requirements for turbines, towers and foundations, and the turbine maker designs to it. The fabricator's obligations are in the fabrication specification that results. You may be asked to support audits connected with certification, so check the quality clauses for access rights and the records you must keep.

How does the turbine's type certificate affect the fabricator?

A type certificate covers a turbine design that has been assessed, and the tower can be part of it. The materials, weld details and tolerances in your package are the ones that design assumes. That is why the turbine maker approves suppliers, audits production and decides every deviation. You do not hold the certificate, but your records support it.

Which execution class applies to wind towers?

Whichever the specification states. The execution class under EN 1090-2 is the designer's choice and sets the level of welding control, inspection and traceability. Check that your certification covers it. If the package calls up EN 1090-2 and gives no class, raise a clarification before pricing. Do not assume one from a previous order.

What certificates does tower plate need?

The plate specification names the inspection document type, usually by reference to EN 10204, and any tests beyond the base material standard. It may also restrict supply to approved mills. Check each certificate against the order for grade, delivery condition and required tests, and tie each shell course to its plate and heat in the section's material list.

What certificates do tower flanges need?

The flange specification states the certificate type and the tests, and it may differ from the plate requirement. Flanges are forged rings with their own serial numbers, so the certificate must match the serial number welded into the section. Check who places the flange order. If the turbine maker supplies flanges, agree who checks the certificates on receipt.

What should a tower section weld map show?

Every weld with its own number: longitudinal seams in each shell course, circumferential seams between courses, the shell-to-flange welds, the door frame and the attachment welds for internals. For each, the log behind the weld map records the procedure, the welder and the date. NDE reports then refer to the same numbers.

How much NDE do tower welds need?

The turbine maker's NDE requirements decide, by weld category. Method and extent usually differ between longitudinal seams, circumferential seams, flange welds and attachments. The values are in the specification and this page does not give them. Build a table of weld number against required method before production starts, so that each report can be ticked off against it.

Is post-weld heat treatment required on tower sections?

Only where the specification asks for it. Most tower packages do not, but check the welding requirements for a clause tied to thickness or to a particular joint. If one exists, you need the equipment, a procedure and a chart for each treatment in the dossier. If none exists, do not add an empty heading to the dossier index.

When is tower flange flatness measured?

At the stage the specification names, which is after the flange has been welded to the shell, because welding distorts it. The flange flatness report should identify the section, the flange, the instrument and the limits used. A reading taken on the loose flange before welding does not show that the finished section complies.

What coating records does a tower section need?

Records for each step of the system on each surface: surface preparation, the conditions during application, each coat applied and the film thickness checks, with the instrument used. The coating specification says which checks are needed and who witnesses them. A common gap is one coat of a multi-coat system with no inspection record in the dossier.

Can we weld brackets for internals to the tower shell?

Only as the drawings and specification allow. Attachment welds on the shell affect the fatigue design, so turbine makers control where they are and how they are made, and some require bolted or magnetic fixings instead. A bracket moved or added in the shop is a deviation that needs the designer's approval before the weld is made.

What goes in a tower fabricator's deviation list?

Standing differences between the package and your shop: an alternative plate mill or flange forge, a welding process or joint preparation, a changed seam layout, an NDE method, the measuring method for tolerances, an equivalent coating system and your report formats. Each row quotes the clause and your proposal. See the technical deviation list guide.

How is a non-conformance on one section handled?

You record it, stop that item where the quality rules say so, and send the turbine maker a concession or deviation request with the facts and your proposed action. The maker decides whether to accept, repair or reject. The request, the answer and any re-inspection go into that section's dossier. Check the contract for how long an answer may take.

What is a tower section dossier?

The complete record set for one section, identified by its serial number and arranged to the turbine maker's index. It holds the certificates, weld and NDE records, dimensional and flatness reports, coating records, any concessions and the release note. It is the tower equivalent of a manufacturing record book. The section ITP template lists the stages that produce it.

How does OdysseyGPT help a tower fabricator?

It checks documents against the turbine maker's requirements and quotes the source for every finding. Document Review compares the fabrication specification with your procedures. Tools in beta check certificates against the order, welds on the map against NDE reports, instruments against calibration certificates and a section's folder against the dossier index. Engineers decide on each finding.

What does OdysseyGPT not do for tower fabricators?

It does not read drawings, assess a design or say whether a deviation is structurally acceptable. It does not measure flange flatness, survey dimensions or judge coating readings, and it certifies nothing. The NDE Coverage Review (beta) needs the weld map as a list or table. It reads only the documents you upload, so a missing specification means missing checks.

Frequently asked questions

What quality documentation does a wind tower section need?

The turbine maker's specification sets the list. It commonly includes plate and flange certificates with traceability, a weld map with welder and procedure records, NDE reports, dimensional and flange flatness reports, coating inspection records and any heat treatment records, compiled as one dossier per section.

Which standard governs wind tower fabrication?

The turbine maker's fabrication specification governs. European specifications commonly build on EN 1090-2 and ISO 3834 and add their own requirements. The IEC 61400 series governs the turbine design, not the shop.

Why is flange flatness measured after welding?

Welding the flange to the shell distorts it. The sections are bolted together through these flanges, so the specification sets limits on the finished flange and asks for a report.

Does OdysseyGPT check flange flatness or coating thickness?

No. It does not measure or judge readings. It checks that the reports exist for the section, match the dossier index and name instruments with valid calibration certificates.

References

IEC 61400-6: Wind energy generation systems. Part 6: Tower and foundation design requirements

IEC

Webstore abstract. Read 15 Nov 2026. The standard is a paid document.

Visit source

DNV-ST-0126 Support structures for wind turbines

DNV

Publisher's description of the standard's purpose.

Visit source

DNV-SE-0441 Type and component certification of wind turbines

DNV

Visit source

UKCA marking of fabricated structural steelwork

SteelConstruction.info (BCSA and SCI)

EN 1090-2 and execution classes.

Visit source

EN 1090-2, ISO 3834, EN 10204 and ISO 12944

CEN and ISO

Paid standards, named here by title and subject only.

Related Pages