OdysseyGPT

Glossary term

Flange Flatness Report

The inspection record of how flat a tower section's flange is after welding, measured around its circumference and compared with the specified limits.

Last reviewed by the OdysseyGPT team

What it is

A flange flatness report records how flat a wind tower section's flange is after it has been welded to the shell. It lists readings around the flange, the limits from the turbine maker's specification, the method, the instrument and the result. Each flange of each section needs one in the section dossier.

Key Takeaways

  • Tower sections bolt together through their flanges, so the finished flange face is controlled.
  • The measurement that counts is the one taken after welding, at the stage the specification names.
  • The report should identify the section, the flange, the instrument and the limits used.
  • An out-of-limit flange is the turbine maker's decision, not the fabricator's.

Why it matters

Steel wind turbine towers are built in sections, and the sections are joined on site by bolting ring flanges together. Each section therefore ends in a flange that is welded to the last shell course. Welding heats one side of the flange and pulls it out of shape, so a flange that left the forge flat may no longer be flat on the finished section. The turbine maker's specification sets limits on the finished flange and asks for proof that each one is within them. The flange flatness report is that proof. A typical report identifies the tower section and which flange it is, the flange serial number, and the stage at which it was measured, since the specification says when the measurement that counts is to be taken. It names the method and the instrument, with the instrument's identity so its calibration can be checked. It records readings at points around the flange and the values worked out from them, for flatness and for the tilt of the flange face. It gives the limits and their source, a result, a date and the inspector's name. The limits come from the turbine maker's specification and drawings, and this entry does not give values. The report matters because a gap between mating flanges changes how the bolts are loaded once they are tightened, and the bolted joint is part of the design that was assessed. A flange outside the limits is a non-conformance that the turbine maker has to decide on. The fabricator cannot accept it alone. The report sits in the section dossier beside the dimensional report, and the two are often confused. The dimensional report covers the section as a whole: length, roundness and straightness.

How OdysseyGPT uses it

OdysseyGPT does not measure a flange and does not judge the readings on a report. It checks the paperwork around it. MRB Readiness Check (beta) reports a dossier index line for a flatness report that has no document behind it, or a report still at an unapproved revision. Calibration Validity Check (beta) matches the instrument named on the report to its calibration certificate and its validity on the measurement date. ITP Validator (beta) checks that the measurement appears in your inspection plan at the level the turbine maker requires.

Evaluation questions

What should a flange flatness report contain?

The section and flange identity, the stage of measurement, the method and instrument with its identity, the readings and derived values, the limits and their source, the result, the date and the inspector.

How does it differ from the dimensional report?

The dimensional report covers the whole section: length, roundness and straightness. The flatness report covers one flange face. A section dossier normally holds both.

Does OdysseyGPT judge the flatness readings?

No. It checks that the report is present, approved, tied to the right section and names a calibrated instrument. Judging the readings is the inspector's work.

Frequently asked questions

What is a flange flatness report?

The inspection record showing how flat a tower section's flange is after welding. It gives readings around the flange, the specified limits, the instrument used and the result.

Why is flange flatness measured after welding?

Because welding the flange to the shell distorts it. The limits apply to the finished flange, so a measurement made before welding does not show compliance.

Who sets the flange flatness limits?

The turbine maker, in its fabrication specification and drawings. The bolted flange joint is part of the tower design, so the limits are not the fabricator's to change.

What happens if a flange is outside the limits?

The fabricator raises a non-conformance and the turbine maker decides: accept, correct or reject. The decision and any re-measurement go in the section dossier.

References

IEC 61400-6: Wind energy generation systems. Part 6: Tower and foundation design requirements

IEC

The design standard for towers and foundations. Paid document; no values are taken from it.

Visit source

DNV-ST-0126 Support structures for wind turbines

DNV

Named for context. Paid document.

Visit source

The turbine maker's fabrication specification and drawings

The source of the limits, the measurement stage and the report format on any real order.

Related Pages