What is EHEDG?
EHEDG stands for the European Hygienic Engineering & Design Group. It was set up in 1989 as a non-profit group that brings together equipment makers, food producers, research institutes, universities and public health authorities. It does three things that an equipment maker meets in practice: it publishes guidelines, it certifies equipment, and it runs training.
EHEDG is not a regulator and its guidelines are not law. They are a body of agreed good practice. A dairy, brewery or food producer makes them part of your contract by naming them in its engineering standard, its hygienic design standard or the order. The name is European, but EHEDG has regional sections in many countries and customers outside Europe cite it too.
How are the EHEDG guidelines organised?
EHEDG says its working groups have produced more than fifty documents. Each has a number, written as Doc followed by the number, and a few are split into parts. The catalogue can be filtered by topic and by language. Company and institute members have access to all of them, and others can buy single guidelines. A small number, such as the glossary, are offered openly.
The numbers are not arranged by subject, so it helps to think of the guidelines in groups. The grouping below is ours, not EHEDG's. The titles are shortened from the public catalogue.
| Kind of guideline | Examples | When a maker meets it |
|---|---|---|
| General principles | Doc 8 on hygienic design principles; Doc 32 on materials of construction; Doc 58 on hygienic design risk management | Cited by nearly every customer standard that mentions EHEDG |
| Closed equipment for liquids | Doc 10 on closed equipment for liquid food; Doc 14 on valves; Doc 16 on pipe couplings; Doc 17 on pumps and homogenisers; Doc 20 on mixproof valves; Doc 25 on mechanical seals | Tanks, skids and pipework cleaned in place |
| Open equipment | Doc 13 on equipment in wet-cleaned open processing areas; Doc 43 on belt conveyors; Doc 55 on bakery equipment | Conveyors, open fillers and machines cleaned by hand or by foam and rinse |
| Dry materials | Doc 22 on dry particulate materials; Doc 31 on spray dryers and fluid beds; Doc 36 and Doc 40 on transfer systems and valves for powders | Powder handling, where wet cleaning is avoided |
| Welding and surfaces | Doc 9 and Doc 35 on welding stainless steel and tubing; Doc 54 on testing hygienic weld joints; Doc 18 on chemical treatment of stainless steel surfaces | Fabrication standards, weld acceptance and passivation clauses |
| Seals and lubricants | Doc 48 on elastomeric seals; Doc 23 on registered food-grade lubricants | Gasket, O-ring and gearbox clauses |
| Cleaning | Doc 50 on cleaning-in-place installations; Doc 51 on tank and vessel cleaning; Doc 45 on cleaning validation; Doc 52 on principles of cleaning and disinfection | Requirements for clean in place and spray devices |
| Whole lines and plants | Doc 34 on integrating hygienic entities; Doc 44 on hygienic design of food factories; Doc 46 on aseptic and hygienic filling machines | Skid and line builders, where certified parts are joined together |
| Test methods | Doc 2 on in-place cleanability; Doc 5 on in-line steam sterilisability; Doc 7 on bacteria tightness; Doc 57 on cleanability of open equipment | Behind the certification scheme, and sometimes cited directly in a FAT clause |
Guidelines are revised, merged and withdrawn. The catalogue shows several older numbers as withdrawn and folded into newer documents. If a customer standard cites a guideline number you cannot find, check the catalogue for where its content went, then ask the customer which document it means.
How does EHEDG certification work?
EHEDG certifies items of equipment, such as a valve, a pump, a sensor or a conveyor component. The public description of the scheme sets out two steps. An Authorised Evaluation Officer reviews the design against the relevant guidelines, comparing a sample with the maker's drawings. Where the scheme calls for it, an Authorised Test Laboratory then tests the item using an EHEDG test method. EHEDG lists both the officers and the laboratories on its website.
A certificate is issued for a named item and is listed in EHEDG's public register of certified equipment. EHEDG states that the certificate records the equipment name, type and sizes, the seal materials tested, the supplier, the certification type and the dates of issue and expiry. The holder confirms each year that the design has not changed, and the certification is renewed after five years with a new review.
EHEDG also notes that its test methods assess suitability under set test conditions and do not show how an item will perform in a particular application. A certificate is evidence about the design of the item. It is not a statement about your customer's product, detergents or cleaning times.
What do the certificate types and classes mean?
The scheme sorts certificates by how the equipment is cleaned. There are two types. Type EL is for equipment cleaned with liquids, and Type ED is for equipment that is dry cleaned only. Each type has classes. The table gives EHEDG's own definitions in our words.
| Type and class | Equipment it covers | What follows for the buyer |
|---|---|---|
| EL Class I | Closed or open equipment that is wet cleaned in place, with no dismantling | The class to ask for where the item sits in a CIP circuit |
| EL Class II | Closed or open equipment that is dismantled for wet cleaning | The cleaning instructions must say what is taken apart, and the site must do it |
| EL Aseptic Class I | Closed equipment that is wet cleaned in place without dismantling, can be steam sterilised and is bacteria tight | For aseptic duties, such as after a steriliser |
| EL Aseptic Class II | Closed equipment that is dismantled for wet cleaning, can be steam sterilised and is bacteria tight after it is put back together | As above, with dismantling in the cleaning routine |
| ED Class I | Closed equipment that is dry cleaned only, without dismantling | Powder handling where no liquid is used |
| ED Class II | Closed or open equipment that is dismantled for dry cleaning only | Powder handling with strip-down cleaning |
EHEDG describes Type EL as needing a design review and cleanability testing, and Type ED as needing a design review. Certificates marked EL Class I AUX, for auxiliary open components such as feet and bearing units, also appear in the register. The class list has changed over the years, so read the current scheme document on ehedg.org before you rely on a class name in an older specification.
Class I and Class II are not grades of quality
The class describes the cleaning method the item was assessed for. An EL Class II item is not a weaker EL Class I item. It is one that must be taken apart to be cleaned. If the customer's line is cleaned in place and never opened, a Class II certificate does not answer the requirement.
What does a customer specification usually ask a supplier to show?
Customer standards cite EHEDG in two quite different ways, and the wording tells you which one you are pricing.
- Design to the guidelines. The standard says the equipment shall be designed in line with EHEDG, sometimes naming documents. This is a requirement on your own design and fabrication, and the evidence is your drawings, your fabrication standard and your records.
- Certified components. The standard says valves, pumps, sensors or couplings shall be EHEDG certified. This is a requirement on what you buy, and the evidence is the certificate for each model.
- A stated type and class. Some standards name the class wanted for each duty. Others say only "EHEDG certified", which leaves the class open.
- Records. Certificates in the dossier, sometimes with a statement from you that the installed arrangement follows the component maker's instructions.
- A test. Some orders add a cleanability or spray coverage test on the finished equipment at the factory acceptance test. That is a contract test on your equipment, separate from any component certificate.
The gap between the first two is where disputes start. A skid built entirely from certified parts can still have a dead end where two parts meet, and a well designed skid can contain an uncertified part with no certified alternative. Say in your offer which of the two you are declaring.
What to check in a specification that cites EHEDG
| Check | Why it matters |
|---|---|
| Which guidelines are named, by number and version | "In accordance with EHEDG" covers more than fifty documents, and the ones for dry materials and for liquids ask for different things |
| Whether the clause asks for design to the guidelines, certified components, or both | One is a statement about your design and the other is a purchasing constraint |
| The type and class wanted for each certified component | A class for dismantled cleaning does not answer a clean-in-place duty |
| Which components must be certified | Certified versions do not exist for every item, and the offer should list the exceptions |
| The exact model, size and seal material on each certificate against your bill of materials | A certificate covers the item and seal materials it names, not the whole product range |
| The expiry date of each certificate against your delivery date | Certificates are time-limited and a lapsed one may be rejected at handover |
| Any roughness, radius or drainage figure the customer writes next to the EHEDG reference | The customer may set its own limit, and the two should be checked against each other in the cited document |
| Whether a cleanability, coverage or drainage test is asked for on your equipment | It adds test time, water, a method and an acceptance rule to agree |
| The installation instructions that come with each certified component | Orientation and connection details can be a condition of hygienic use |
| Whether the standard also cites 3-A, and which governs | The two schemes are separate, and one certificate does not stand in for the other |
| The documents wanted in the dossier for each EHEDG clause | Certificates must be collected from component suppliers while the parts are on order |
OdysseyGPT's Document Review sets the customer's standard beside your datasheets, fabrication standard and quality plan and drafts the compliance matrix and deviation list, with a quote from each side on every row. Customer Specification Review (beta) lists each obligation in the customer's text with its clause, including every mention of a guideline or certificate. The sector picture is on the food processing equipment manufacturers page.
What OdysseyGPT does not do here
It compares written documents. It does not hold the EHEDG guidelines, does not review a design against them, does not read drawings and does not test cleanability. It does not certify equipment and cannot confirm that a certificate is current: look the item up in EHEDG's own register.
Talk through your tender review
See how OdysseyGPT reviews a tender
Tell us how your team reviews tenders today. We can walk through an example together.
