What is ASME BPE?
ASME BPE, Bioprocessing Equipment, is a standard published by the American Society of Mechanical Engineers. ASME describes its scope as the design of equipment used in the bioprocessing, pharmaceutical and personal-care products industries, and other applications with relatively high hygienic requirements. It covers materials, design, fabrication, inspection, testing and certification, and applies mainly to new fluid processing equipment where a defined level of purity and bioburden control is required.
It was first issued in 1997 and has been revised regularly since, with new editions about every two years in recent cycles. ASME published a 2026 edition, and earlier editions such as 2022 and 2024 are still named in live contracts. The ASME B31.3 process piping code refers to it. It is a voluntary consensus standard, not a regulation: it applies to your equipment when the purchase order, the specification or the URS says so.
How ASME BPE is organised
| Part | Subject | Why a maker reads it |
|---|---|---|
| GR | General requirements | Scope, terms, inspection and documentation rules that apply across the standard |
| CR | Certification requirements | The rules behind ASME's BPE certification programme |
| MM | Metallic materials | Which stainless steels and higher alloys are listed, and what is asked of them |
| PM | Polymeric and other non-metallic materials | Elastomers, polymers and the compliance evidence they need |
| SD | Systems design | Cleanability, drainability, dead legs and design for cleaning and steaming in place |
| DT | Dimensions and tolerances | Tube and fitting dimensions, so parts from different makers fit and drain |
| PI | Process instrumentation | Hygienic instrument design and installation |
| MC | Components | Valves, seals, pumps, hoses and other process components |
| MJ | Materials joining | Welding of hygienic systems, including weld acceptance and examination |
| SF | Process contact surface finishes | Surface finish designations and acceptance criteria |
| SU, SC, SJ | Single-use systems, components and joining | Requirements for single-use equipment |
A public summary of the 2026 edition reports changes across most parts, including materials, systems design, materials joining, surface finishes, single-use and process instrumentation. If a URS names an edition older than the one your procedures follow, or the other way round, raise it as a clarification before you quote.
Surface finish designations
The surface finish part gives a set of designations for product-contact surfaces, written SF0 to SF6 in public summaries. One designation means no finish requirement. One group is mechanically polished. Another group is mechanically polished and then electropolished. Each designation has its own maximum roughness, given as Ra, and the part also sets acceptance criteria for surface defects such as pits, scratches and weld discolouration.
- The numbers are codes, not a scale from rough to smooth. Do not assume a higher number means a finer finish.
- An electropolished designation cannot be met by mechanical polishing alone, even if the measured roughness is low enough.
- The roughness limit is a maximum for each reading, not an average across the part.
- If a URS gives both a designation and a roughness number, check that they agree and which one governs.
- Read the limits in the edition your contract names. We do not reproduce the table here.
Welding and weld documentation
The materials joining part covers welding of hygienic tube, fittings and equipment, including orbital welding, weld acceptance criteria and examination. Heat tint, the discolouration next to a weld, is judged against reference colour charts that ASME sells separately. The 2026 edition is reported to add guidance on heat tint limits for orbital welds and a welding operator qualification example aligned with ASME B31.3.
A URS usually goes further than naming the standard. It may set the share of welds to be examined by borescope, ask for a weld map and weld log linked to welder, procedure and heat number, and require passivation records. Compare each of these with your own quality plan. Where the URS asks for more than your standard practice, price it or list it as a deviation.
Design for cleaning and draining
The systems design part deals with how equipment is laid out so it can be cleaned, drained and, where needed, steamed in place. It covers topics such as slopes and drainability, dead legs in branches, and the design of vessels, pumps, valves and other items for cleaning in place (CIP) and steaming in place (SIP). Dead legs are commonly discussed as a ratio of branch length to diameter, and public commentary cites a target of two or less in recent editions, measured in the way the standard defines.
These requirements show up on drawings: P&IDs, isometrics and general arrangements. A written statement in your specification that the system is drainable is not the same as a drawing that shows the slope. State in your URS response which document proves each design requirement.
Materials, certificates and certification
The metallic materials part lists austenitic stainless steels and higher alloys, including superaustenitic, duplex and nickel alloys in recent editions. Customers usually pair it with a material certificate requirement, most often EN 10204 type 3.1 for product-contact parts, and with compliance statements for elastomers and polymers.
ASME runs a BPE certification programme. It certifies the quality management system of organisations that make certain BPE products, such as tubing and fittings, and public reports say the 2026 edition extends it. ASME publishes a directory of certificate holders. A URS that asks for "BPE certified" components means parts from a certificate holder, which is different from a statement that your equipment is designed to the standard.
What to check in a tender or URS against ASME BPE
| Check | Why it matters |
|---|---|
| Edition of ASME BPE named in the URS, specification and datasheets | Documents in one package often name different editions, and part letters and content change between them |
| Which parts of the scope BPE applies to: product contact only, or utilities and supports too | Applying it to the whole skid changes material, finish and documentation cost |
| Surface finish designation and any roughness number, for each surface | The two can disagree, and electropolish is a separate process step |
| Electropolishing and passivation: required or not, and the record asked for | Often subcontracted, with its own lead time and report |
| Weld examination extent, including borescope share and who selects the welds | A higher share than your standard practice is a direct cost |
| Weld map, weld log and the fields the customer wants in them | Formats differ, and re-keying records at the end is slow |
| Heat tint acceptance and the reference used | A stricter limit than your procedure raises the repair rate |
| Drainability, slope and dead leg limits, and the drawing that proves each | These are design decisions, hard to change after fabrication starts |
| Materials listed for product-contact parts, and certificate type for each | Bought-in components may not come with the certificate the URS asks for |
| Elastomer and polymer compliance statements required | Each statement has to be collected from the component supplier |
| Whether components must come from ASME BPE certificate holders | Restricts your supplier list and may change price and delivery |
| Spray device coverage or cleanability testing, and where it is done | Adds test time at the FAT, or a site test you must support |
| The turnover package index and document formats | Sets the records you must keep from the first day of fabrication |
OdysseyGPT's Document Review checks a customer's URS and specifications against your own datasheets, fabrication specification and quality plan, and drafts the compliance matrix and deviation list, each row quoting its source. After the order, the Material Certificate Review (beta) checks certificates against the purchase requirements, and the Welding Qualification Review (beta) checks that procedures and welder qualifications cover each weld on a weld list.
What OdysseyGPT does not do here
It reads written documents. It does not interpret P&IDs, isometrics or other drawings, so it cannot check a slope or a dead leg. It does not hold a copy of ASME BPE and does not judge your design against the standard: it compares the documents you upload. It does not perform qualification.
Talk through your tender review
See how OdysseyGPT reviews a tender
Tell us how your team reviews tenders today. We can walk through an example together.
