What is IEC 60076?
IEC 60076 is published by the International Electrotechnical Commission under the general title Power transformers. Technical committee 14 maintains it. Part 1, General, applies to three-phase and single-phase power transformers, including auto-transformers. It leaves out some small and special categories, such as instrument transformers, welding transformers and traction transformers mounted on rolling stock.
Part 1 holds the definitions, service conditions, rating rules, tapping rules, connection symbols, rating plate content, tolerances and the general test requirements. The other parts each take one subject, such as temperature rise or dielectric testing, or one kind of transformer, such as dry-type units. Where a kind of transformer has its own part, Part 1 applies only as far as that part calls it up.
Editions move part by part
Each part of the series is revised on its own timetable, and many countries publish the parts as national standards under their own numbers. A tender may name an edition older than the current one. State in your offer which edition of each part your design and your type test reports follow.
Which parts make up the IEC 60076 series?
The table lists the parts a tender engineer meets most often, by title. It is not the full series, and it gives no requirements. The IEC website carries the current list and editions.
| Part | Subject | Why it matters in a tender |
|---|---|---|
| IEC 60076-1 | General | Definitions, ratings, tappings, tolerances, rating plate and the split of tests into routine, type and special |
| IEC 60076-2 | Temperature rise for liquid-immersed transformers | The basis for the temperature rise guarantee and the test that proves it |
| IEC 60076-3 | Insulation levels, dielectric tests and external clearances in air | The insulation level in the schedule and the dielectric tests that go with it |
| IEC 60076-5 | Ability to withstand short circuit | How short-circuit withstand is shown, which is where buyers ask for test evidence |
| IEC 60076-6 | Reactors | Applies when the lot includes reactors |
| IEC 60076-7 | Loading guide for mineral-oil-immersed power transformers | Cited when the tender sets overload duties |
| IEC 60076-10 | Determination of sound levels | The method behind the guaranteed sound figure |
| IEC 60076-11 | Dry-type transformers | The governing part for cast resin and other dry-type units |
| IEC 60076-12 | Loading guide for dry-type power transformers | The dry-type counterpart to Part 7 |
| IEC 60076-13 | Self-protected liquid-filled transformers | A distribution transformer type with its own part |
| IEC 60076-14 | Liquid-immersed power transformers using high-temperature insulation materials | Applies when the design uses such materials |
| IEC 60076-15 | Gas-filled power transformers | A transformer type with its own part |
| IEC 60076-16 | Transformers for wind turbine applications | Named in wind farm tenders |
| IEC 60076-18 | Measurement of frequency response | The method when a tender asks for a frequency response record at the works or on site |
Components are covered elsewhere. Part 1 refers out to separate IEC standards for bushings, tap-changers and insulating oil. A tender that wants certificates for those components is asking for evidence against those standards, not against IEC 60076 itself.
Routine, type and special tests: what is the difference?
Part 1 puts every test into one of three categories. The category decides how often the test is made and who pays for it by default. See type test vs routine test for the short version.
| Category | When it is made | Examples named in the Part 1 test clause | Usual evidence |
|---|---|---|---|
| Routine test | On every transformer | Winding resistance, voltage ratio and phase displacement check, short-circuit impedance and load loss, no-load loss and current | A routine test report for each serial number |
| Type test | On one transformer that represents the others of the same design | Temperature rise is the usual example | A type test report, either new for the order or an existing one the buyer accepts |
| Special test | Only when the purchaser asks for it and it is agreed | Short-circuit withstand and frequency response are often asked for in this way | A report for the unit tested, as the contract sets out |
Two points catch bidders out. First, the lists are not the same for every transformer. The standard assigns some tests to a different category depending on the voltage class, so a test that is routine for a large transmission unit may be a type or special test for a smaller one. Second, the purchaser may move a test up, for example by asking for a type test on every unit. Read the test clause of the edition named in your contract, then read the tender's own test list beside it.
Besides the electrical measurements, Part 1 has clauses on on-load tap-changer operation tests, leak testing with pressure, vacuum and pressure deflection tests on the tank, and a check of core and frame insulation. For what these look like on the test floor, see transformer testing.
What does IEC 60076-1 expect the purchaser to state?
The standard leaves a number of choices to agreement between manufacturer and purchaser, and says these should be raised early and written into the contract specification. Part 1 has a clause on the extra information an enquiry needs, covering matters such as winding connection, sound level and transport. It also has an informative annex that is a checklist of the information to provide with an enquiry and an order.
For a bidder this is useful in reverse. Where a tender is silent on a point the annex lists, you have grounds for a clarification question. Where the tender answers it in a schedule, that line belongs in your guaranteed technical particulars and in your compliance matrix.
Part 1 also has a tolerances clause. It applies to certain guaranteed quantities when the contract does not say otherwise. Many utility specifications do say otherwise, and some allow no tolerance above the guaranteed loss. This page does not reproduce the figures. Compare the tender's wording with the edition it names.
IEC 60076 or IEEE C57?
Buyers in North America and some other markets specify IEEE standards. For liquid-immersed transformers the general requirements are in IEEE C57.12.00 and the test methods in IEEE C57.12.90. Dry-type transformers have their own pair, C57.12.01 and C57.12.91. The IEEE Transformers Committee maintains them.
The two families overlap but are not interchangeable. Test names, test categories and rating conventions differ. If a tender cites both, or cites IEEE for the transformer and IEC for its components, ask which governs before you fill in the schedules.
How does OdysseyGPT help with an IEC 60076 tender?
Document Review takes the tender specification and its schedules as the base and checks your datasheet, filled schedules, test procedure and list of type test reports against it. For each requirement it gives a status and quotes the passage in both documents. It also works in reverse and lists statements in your documents that the tender does not answer.
- Customer Specification Review (beta) turns the specification into a register with one line per test, rating or document obligation.
- Datasheet Comparison (beta) sets the buyer's transformer schedule beside your filled copy and lists the fields that differ.
- ITP Validator (beta) checks your inspection and test plan against the buyer's test and witness clauses.
- Calibration Validity Check (beta) matches the instruments named in a routine test report to their calibration certificates.
What it does not do
OdysseyGPT does not test a transformer, calculate a loss or a temperature rise, or decide that an old type test report still represents your design. It does not read drawings. It has no copy of IEC 60076, so it checks against the standard only where you upload the edition as readable text. Engineers decide every status.
What to check in a transformer tender against IEC 60076
Use this as a reading list for the tender, not as a statement of what the standard requires. Each line names something to find in the tender and in your own documents.
| Check | Look in the tender for | Look in your documents for |
|---|---|---|
| Parts and editions | Which parts of IEC 60076 are named, with or without a year, and any national equivalent | The editions your design standard and type test reports state |
| Order of precedence | Which document wins when the specification, schedules and standards disagree | Any offer text that assumes a different order |
| Service conditions | Altitude, ambient temperature and other conditions outside what the standard treats as normal | The conditions your ratings are based on |
| Rating and cooling | Rated power for each cooling mode, voltages, tapping range and connection symbol | The same fields on your datasheet, on the same basis |
| Guaranteed losses and impedance | Guaranteed figures, how losses are evaluated, and penalty or rejection terms | Which figures you mark guaranteed and which typical |
| Tolerances | Whether the standard's tolerances apply or the buyer sets its own | Any tolerance wording in your schedules or offer letter |
| Routine test list | Tests the buyer adds to the routine list for every unit | Your works routine test procedure and report format |
| Type tests | Which type tests must be made on this order and which may be covered by a report | Your list of type test reports, with design, date and laboratory |
| Special tests | Each special test asked for, on which unit, and who pays | Whether the offer includes, prices or excludes each one |
| Witnessing | Which tests are witnessed, the notice period and who attends | Hold and witness points in your ITP |
| Components | Standards and approved makes for bushings, tap-changer and insulating liquid | The makes and certificates you offer |
| Sound level | The guaranteed figure and the measurement basis | The basis stated on your datasheet |
| Transport and site | Transport limits, impact recording, site tests and commissioning scope | What your offer includes after the works tests |
| Test records | Report format, calibration certificates for instruments and the final dossier index | Your standard report and what it leaves out |
Talk through your tender review
See how OdysseyGPT reviews a tender
Tell us how your team reviews tenders today. We can walk through an example together.
