What is NSF/ANSI/CAN 61?
NSF/ANSI/CAN 61, Drinking Water System Components: Health Effects, sets minimum health effects requirements for the chemical contaminants and impurities that products and materials can pass into drinking water. It applies from the source to the tap: to anything that touches drinking water or a drinking water treatment chemical on the way. The three parts of the name show that it is published by NSF and is a national standard in both the United States and Canada. Most people shorten it to NSF 61.
The standard is narrow on purpose. By its own scope it does not set performance, taste and odour or microbial growth requirements. A valve listed to it has been evaluated for what it releases into the water. Whether it seals, lasts or meets a pressure rating is a matter for the product standard, such as one of the AWWA standards. Point-of-use treatment devices for homes are covered by other NSF standards, and treatment chemicals themselves by NSF/ANSI/CAN 60.
In the United States the standard gets its force from state drinking water regulations and plumbing codes that require products in public water systems to conform, and from project specifications. Canadian provinces and territories refer to it in a similar way. Check what the authority for your project requires.
Which products does NSF/ANSI/CAN 61 cover?
The standard is divided into sections by product type, and each type is evaluated in its own way. The table is our own summary of how NSF describes them.
| Product group | Examples | What a supplier should note |
|---|---|---|
| Pipes and related products | Pipe, tubing, hose and fittings | A listing may be limited to a size range and to cold or hot water |
| Barrier materials | Coatings, linings and paints applied to tanks, pipe, valves and pumps | The listing belongs to the coating product. It can set limits on how the coating is applied and cured |
| Joining and sealing materials | Gaskets, sealants, adhesives and lubricants | Small parts, but a section that says "all wetted materials" includes them |
| Process media | Filter media, activated carbon and ion exchange resins | Listed by product and grade |
| Mechanical devices | In-line valves, water meters, filters, chemical feeders and process equipment | Where most treatment plant equipment sits. Confirm with your certifier which section your product is evaluated under |
| Mechanical plumbing devices | Taps, drinking fountains and other devices at the end of the line inside buildings | Seldom relevant to plant equipment |
A component can be certified on its own, and so can a finished product. They are not the same thing. Using a certified coating or a certified gasket helps the evaluation of the finished valve or pump, but it does not make the assembly certified. NSF gives the example of a chemical feed pump: certifying the pump does not certify the tubing as a product in its own right.
Who certifies products, and what is a listing?
NSF wrote the standard and is also the best-known certifier, which is why the two are often confused. Other accredited certification bodies certify to the same standard, among them UL Solutions and IAPMO R&T. A mark from any of them is evidence of certification to the standard. Some specifications name one body. If yours does and your listing is from another, raise it before bid day.
Certification follows broadly the same path at each body. As NSF describes it, the maker applies and discloses the formulation of every material that touches water. Toxicologists review the formulations and decide which chemical analyses are needed. The production site is audited. Samples are exposed to test waters, the water is analysed, and the results are judged against health-based criteria. Those criteria now sit in a companion document, NSF/ANSI/CAN 600, which the standard refers to.
A product that passes is entered in the certifier's public directory. That entry is the listing. Certification does not end there: NSF describes annual review, unannounced inspections of the production site and periodic retesting. A change of material, supplier or production site can affect the listing, so a listing checked last year should be checked again for a new order.
Read the listing, not the logo
The directory entry names the company, the production site, the product or model and any conditions, such as size range, water contact temperature or the materials covered. An engineer reviewing a submittal compares that entry with the model and options on the order. A mark on a brochure does not show which variants are covered.
How does NSF/ANSI/CAN 61 relate to NSF/ANSI/CAN 372 and lead content?
The two standards ask different questions. NSF/ANSI/CAN 61 asks what a product releases into water, lead included. NSF/ANSI/CAN 372 asks how much lead the product contains, worked out as a weighted average over the wetted surfaces of its materials.
The second question comes from United States law. The Safe Drinking Water Act defines "lead free" for pipes, fittings and fixtures as a weighted average of not more than 0.25 per cent lead across the wetted surfaces, and the Environmental Protection Agency's rule requires manufacturers and importers to certify that covered products meet it. The Act exempts some products, including fire hydrants and water distribution main gate valves of 2 inches and larger. NSF states that products certified to NSF/ANSI/CAN 61 also meet NSF/ANSI/CAN 372 unless the Act exempts them.
For a supplier the practical point is that a specification may ask for both, in one sentence or two. Answer each one. If your product falls under a statutory exemption, say which, and do not assume the engineer's specification allows the exemption. A project specification can ask for more than the law does.
What is a supplier asked to submit?
- A copy of the current listing from the certification body's directory for the product offered, showing the model, size and material covered.
- The listing for each coating or lining applied to wetted surfaces, where the finished product is not itself listed.
- A statement tying the listing to this order: the model and options to be supplied are the ones the listing covers.
- Evidence of lead content compliance, or the exemption relied on, where the specification or the law asks for it.
- For site-applied or shop-applied coatings, the application and cure records, where the listing sets conditions for them.
- The UK equivalent where the project is in the United Kingdom. The buyer may ask for approval under Regulation 31 for products a water company uses in public supply, or for WRAS approval for fittings in premises. Neither is the same as an NSF/ANSI/CAN 61 listing.
These items go into the certificates part of a construction submittal. They are usually wanted with the first submission, before the product data is approved, and are tracked on the submittal log like any other item.
What to check in a tender that names NSF/ANSI/CAN 61
| Check | Why it matters |
|---|---|
| Does the requirement apply to this equipment at all | Wastewater and raw water equipment may sit in a manual whose general sections copy a potable water clause. Ask if it is unclear |
| Whether the section wants the finished product listed or only its wetted materials | "Certified product" and "certified materials" are different offers with different evidence |
| Model, size and material on the schedule against the listing | A listing can stop short of the largest sizes or exclude an optional material |
| Coatings and linings named in the section against the listed coating | A named coating that is not the one your listing was granted with may void the evidence |
| Water temperature and any other condition on the listing | Some listings are for cold water contact only |
| Elastomers, lubricants and sealants | A wording such as "all materials in contact" reaches the small parts |
| Which certification body the section names | Some sections name one. Raise a clarification if your listing is from another accredited body |
| Lead content wording, and any exemption you rely on | The section may ask for more than the statute |
| Production site on the listing against where this order will be made | Listings are tied to sites. A second works may not be covered |
| When the evidence is due | Often with the first submittal. A listing that is still in progress is an exception to declare |
| Any national approval asked for in place of or as well as the listing | Regulation 31 and WRAS approval in the United Kingdom are separate regimes with their own lists |
OdysseyGPT cannot certify a product or confirm that a listing is valid. Only the certifier's directory shows that. What it does is read documents: Document Review checks a specification section against your product data, certificates and scope letter and shows, with a quote from each, where the section asks for drinking water contact evidence that your package does not state. An engineer then checks the listing itself. For the whole bid and submittal process, including the shop drawing submittal, see the page for water and wastewater equipment manufacturers.
Talk through your tender review
See how OdysseyGPT reviews a tender
Tell us how your team reviews tenders today. We can walk through an example together.
