OdysseyGPT

Standards explainer

AWWA standards for equipment makers: how they are organised, C504, C509 and C515, and what to check in a specification

A plain-English map of the American Water Works Association standards that valve, gate, actuator, pump and coating suppliers are asked to meet, ending with a checklist for a specification that names one.

By Ademola Afolabi, Founder, New Odyssey Ltd · Last reviewed:

The short answer

AWWA standards are consensus standards from the American Water Works Association that set minimum requirements for water supply products and practices. They are grouped by subject: source, treatment, pipe and accessories, storage, pumps, plant equipment and utility management. Equipment makers mostly meet the valve, actuator, slide gate, pump and coating standards, such as C504 and C509.

Key Takeaways

  • AWWA writes standards. It does not test, certify or approve products, so conformance is the maker's own statement backed by records.
  • The letter in the number shows the subject group. Valves, hydrants, actuators and slide gates are in the C500 range.
  • Each standard leaves choices to the purchaser. A specification that names the standard and nothing else has not fully defined the product.
  • Drinking water contact is a separate question, usually answered by an NSF/ANSI/CAN 61 listing.

See how OdysseyGPT reviews a tender. Tell us how your team reviews tenders today. We can walk through an example together. Book a call

What are AWWA standards?

The American Water Works Association (AWWA) publishes more than 200 standards for the water sector. They are written by volunteer committees, go through public review and are accredited by the American National Standards Institute, which is why the full designation reads ANSI/AWWA followed by the number. AWWA describes them as minimum requirements. A utility or its engineer adopts one by naming it in a specification or purchase document.

Two points matter to a supplier. First, AWWA does not test, certify or approve any product. A phrase such as "AWWA approved" in a specification can only mean that the product conforms to the named standard, and the evidence is the maker's statement and the records the standard requires. Second, the standards are not complete purchase specifications. Each one lists options and information the purchaser is expected to supply, and until those are settled the product is not fully defined.

AWWA also publishes manuals of practice, numbered with an M. A manual gives guidance on design or operation. It is not a standard, and a specification that cites one is pointing to guidance, not to a set of product requirements.

How are AWWA standards organised?

AWWA lists its standards by subject, and the letter at the front of each number follows the subject. The table shows the groups an equipment maker will see cited. It is our own summary of the public list.

AWWA standards by subject group (own summary of the public AWWA standards list)
GroupNumberingWhat it coversWho meets it
SourceAWells and source waterWell drillers and well equipment suppliers
TreatmentBFilter media, softening, membrane systems and treatment chemicals for disinfection, coagulation, corrosion control, taste and odour control and fluoridationMedia and chemical suppliers, and makers of membrane and filter packages
Pipe and accessoriesCDuctile-iron, steel, concrete and plastic pipe and fittings, their linings and coatings, valves and hydrants, pipe installation, disinfection of facilities, meters and service linesPipe and fitting makers, valve, hydrant, actuator and gate makers, coating applicators and meter makers
StorageDWater storage tanks and their coating and inspectionTank fabricators and erectors
PumpsESubmersible vertical turbine pumps, and horizontal centrifugal and vertical line shaft pumpsPump makers
Plant equipmentFFibreglass troughs, launders, weir plates and baffles, ultraviolet disinfection systems and ozone systemsMakers of clarifier and filter internals and disinfection equipment
Utility managementGHow a utility runs its treatment plants, distribution system, security and conservation programmesThe utility itself. A supplier seldom has to conform to these

Within the pipe and accessories group the hundreds digit narrows the subject. The C100s are ductile-iron pipe and fittings, the C200s steel pipe and its coatings, and the C500s valves, hydrants, actuators and slide gates. A specification section for valves will usually cite several numbers from the C500 range together with a coating standard.

Which AWWA valve standards do makers meet most?

The valve standards are product standards. Each covers one type of valve for waterworks service and deals with materials, design, testing and the information to be supplied. The table gives the subject of each at title level. Size ranges, pressure classes and test requirements are in the standards themselves and change between editions.

AWWA valve, actuator and gate standards at title level (own summary; read the edition your contract names)
StandardSubjectWhat a bid engineer should note
AWWA C500Metal-seated gate valves for water supply serviceThe older gate valve type. Still named for large sizes and for replacement work
AWWA C504Rubber-seated butterfly valvesThe butterfly valve standard that plant and transmission main specifications cite most. The standard defines valve classes, and the specification should state which one applies
AWWA C509Resilient-seated gate valves for water supply serviceCovers iron-body gate valves with a resilient seat, in non-rising stem and outside screw and yoke forms
AWWA C515Reduced-wall, resilient-seated gate valves for water supply serviceA separate standard from C509 for a lighter body. A specification that names only one of the two may exclude the other
AWWA C507Ball valvesCheck the size range in the title of the edition named against the schedule
AWWA C508 and C518Swing-check valves and double-disc swing-check valves for waterworks serviceCheck which closure control options the section asks for
AWWA C512Air-release, air and vacuum, and combination air valves for water and wastewater serviceOne of the valve standards that names wastewater service in its title
AWWA C516 and C519Large-diameter rubber-seated butterfly valves, and high-performance waterworks butterfly valvesSeparate standards from C504. Check that the number cited matches the valve size and type on the schedule
AWWA C517Resilient-seated, cast-iron eccentric plug valvesCommon in wastewater and sludge service
AWWA C520Knife-gate valvesCommon on sludge and slurry lines
AWWA C530Pilot-operated control valvesPressure reducing, relief and altitude duties
AWWA C541 and C542Hydraulic and pneumatic cylinder and vane-type actuators, and electric motor actuators, for valves and slide gatesOften supplied by a third party. The valve maker still answers for the assembly in the submittal
AWWA C560 to C563Slide gates: cast-iron, fabricated stainless-steel, fabricated aluminium and fabricated compositeThe material decides the standard. The section's leakage and deflection wording may go further than the standard

AWWA C504 is the one searched for most. In outline, it sets minimum requirements for rubber-seated butterfly valves in waterworks service: materials, design, testing and the data the maker supplies. Recent editions describe its use across raw, potable, waste and reclaimed water. The classes and test details are for the reader to take from the edition named in the contract.

Valves for oil, gas and process plants are built to a different family of standards. If your product range serves both markets, see the API valve standards hub and the page for valve manufacturers.

Which AWWA pump, coating and lining standards come up?

AWWA pump, coating and lining standards at title level (own summary)
StandardSubjectWhere it appears
AWWA E102Submersible vertical turbine pumpsWell and booster pump sections
AWWA E103Horizontal centrifugal and vertical line shaft pumpsHigh-service, raw water and transfer pump sections, often next to a Hydraulic Institute test standard
AWWA C550Protective interior coatings for valves and hydrantsCited inside most valve sections for the wetted surfaces of the valve
AWWA C116Protective fusion-bonded epoxy coatings for the interior and exterior surfaces of ductile-iron and grey-iron fittingsFitting and some valve body sections
AWWA C210Liquid-epoxy coatings and linings for steel water pipe and fittingsSteel pipe, fabricated steel fittings and sometimes fabricated equipment
AWWA C213Fusion-bonded epoxy coatings and linings for steel water pipe and fittingsSteel pipe and fittings
AWWA C104Cement-mortar lining for ductile-iron pipe and fittingsDuctile-iron pipe sections

A coating standard and a drinking water contact standard answer different questions. The AWWA coating standard deals with how the coating is applied and tested. Whether the coating material is acceptable in contact with drinking water is normally covered by a listing to NSF/ANSI/CAN 61, which project specifications commonly call for alongside the AWWA number. The exterior paint system for exposed equipment is usually in a separate painting section of the project manual, not in an AWWA standard.

What to check in a specification against the AWWA standard it names

Checks to make before you quote or submit against a named AWWA standard
CheckWhy it matters
The standard number and the edition in the section, the schedule and the purchase orderEditions are revised every few years and scope can change. Documents in one package often cite different ones
Whether the number fits the valve type and size on the scheduleSimilar valves fall under different standards by size, wall thickness or seat type, as with C504 and C516 or C509 and C515
The purchaser options and data the standard leaves to the buyerIf the section is silent on an option, your standard choice becomes the offer. Say which you have assumed
Requirements in the section that go beyond the standardNamed materials, heavier shafts, thicker coatings or extra tests are common. Each is a cost or an exception
Class, rating and service stated in the sectionThe standard offers classes. The section has to pick one, and the schedule sometimes picks another
Test requirements: which tests, on how many units, witnessed or notA proof-of-design test already on file and a production test on every valve are different things
Coating standard, coating material and drinking water contact listingThree separate requirements that are often written as one sentence
Actuator standard and who supplies the actuatorThe actuator may be to C541 or C542 and bought in. The submittal must still show the assembled unit meets the section
The wording of the conformance statement wantedSome sections want an affidavit of compliance in set words, signed by an officer of the maker
Records to be submitted: test reports, material certificates, coating recordsThey belong on the submittal log with a date
Domestic preference clauses alongside the standardConforming to the standard says nothing about where the casting was poured

OdysseyGPT does not hold AWWA standards and does not check a product against one. Document Review checks the specification section against your own product data, statements and test procedures and drafts a matrix and a list of exceptions, with a quote from both documents on every row. If you upload the edition of the standard your contract names, as readable text, it can be part of the review. After award, the ITP Validator (beta) compares your inspection and test plan with the section's test articles. For how the whole bid and construction submittal fit together, see the page for water and wastewater equipment manufacturers.

Talk through your tender review

See how OdysseyGPT reviews a tender

Tell us how your team reviews tenders today. We can walk through an example together.

Book a call

Frequently asked questions

What is AWWA C504?

The AWWA standard for rubber-seated butterfly valves in waterworks service. It covers materials, design, shop testing and the data the maker supplies. Very large valves and high-performance butterfly valves have their own standards, C516 and C519.

What is the difference between AWWA C509 and C515?

Both cover resilient-seated gate valves for water supply service. C515 is the standard for reduced-wall valves, which have a thinner body wall than C509 valves. A specification may accept either or name only one, so check before you offer.

Does AWWA certify or approve products?

No. AWWA writes standards and states that it does not test, certify or approve any product. Conformance is declared by the manufacturer and supported by the records the standard and the specification require.

Are AWWA standards mandatory?

Not in themselves. A standard becomes a requirement when a utility, an engineer's specification, a purchase order or a regulator adopts it. Once the contract names it, the named edition is binding on the supplier.

Do AWWA standards cover wastewater equipment?

Some do. Several valve standards name wastewater or reclaimed water service, and AWWA publishes a standard for membrane bioreactor systems and one for ultraviolet disinfection of wastewater. Most of the catalogue is written for water supply, so check the scope of each one.

References

AWWA standards list

American Water Works Association

Standard numbers, titles and subject groups. Read 15 Nov 2026. The standards themselves are paid documents; buy the edition your contract names.

Visit source

AWWA standards programme

American Water Works Association

How standards are developed, reviewed and accredited.

Visit source

AWWA standards: valves and hydrants

ANSI Webstore

Catalogue entries and public previews, used for scope statements and forewords.

Visit source

NSF/ANSI/CAN 61: Drinking Water System Components, Health Effects

NSF

The drinking water contact standard cited alongside AWWA product standards.

Visit source

Related Pages