What does the Marine Equipment Directive cover?
Directive 2014/90/EU sets one approval system for marine equipment across the EU. It replaced Directive 96/98/EC from 18 September 2016. Two tests decide whether it applies to an item you supply.
- The ship. The directive applies to equipment placed, or to be placed, on board an EU ship: one that flies the flag of a member state and falls within the international conventions. It applies wherever the ship is when the equipment is fitted, so a hull built in Asia for an EU flag is in scope.
- The item. The directive applies to equipment for which the international instruments require approval by the flag state administration. The conventions it names are SOLAS, MARPOL and COLREG.
That second test is why the directive covers life-saving appliances, fire protection, pollution prevention, navigation and radio equipment and similar items, and does not cover most machinery. A cargo pump or a main switchboard is usually a matter for the classification society. A lifejacket, a fire damper or a navigation light is a matter for the flag.
Not legal advice
This page is a summary for engineers who read shipyard enquiries. It is not legal advice. Whether an item is in scope is decided by the directive and the implementing regulation in force. Ask your notified body if you are unsure.
What is the wheel mark?
The wheel mark is the directive's conformity mark, a ship's wheel symbol. It tells a surveyor or port state inspector that the item went through the directive's conformity assessment.
- The manufacturer affixes it, at the end of production, to the product or its data plate. It must be visible, legible and indelible.
- It is followed by the identification number of the notified body, where that body is involved in the production control phase, and by the year the mark was affixed.
- It may not be put on a product that the directive does not cover.
- The directive allows an electronic tag to supplement or replace the mark for items the Commission identifies. EMSA describes a data matrix code that can be scanned to look the product up.
The wheel mark is not the CE marking and not a class approval. A product can carry a CE marking under another directive, hold a class type approval certificate and still lack the wheel mark, or the other way round.
Which conformity assessment modules does the MED use?
The directive offers a short set of routes, each involving a notified body. The implementing regulation states which of them may be used for each item, so the choice is not always open.
| Module | Name | Used |
|---|---|---|
| B | EC type-examination | The design stage. A notified body examines the design and a specimen. Always paired with D, E or F |
| D | Production-quality assurance | With module B, where the maker runs an approved quality system for production |
| E | Product-quality assurance | With module B, where the approved quality system covers final inspection and testing |
| F | Product verification | With module B, where the notified body verifies the products themselves |
| G | EC unit verification | On its own, for equipment produced singly or in small quantities and not in series |
For a maker the difference is practical. B with D or E means quality system audits and then marking by the maker. B with F or G means the notified body is at the works for the products. Know which route your certificates are issued under, because a yard may ask for the module certificates by name.
What do notified bodies and the declaration of conformity do?
A notified body is an independent organisation that a member state has designated to carry out the directive's conformity assessment. Several classification societies also act as notified bodies, through a part of the organisation set up for that role. The approval they give under the directive is a different act from class approval.
- The manufacturer draws up an EU declaration of conformity and takes responsibility for the product.
- A copy of the declaration goes to the ship and is kept on board for as long as the equipment is fitted. A copy also goes to the notified body.
- The manufacturer keeps the technical documentation and the declaration for at least ten years after the mark is affixed, and not for less than the expected life of the equipment.
- A manufacturer outside the EU appoints an authorised representative in the EU by written mandate.
For a shipyard this means paper that has to arrive with the goods. The declaration is a ship's document. If it is missing at delivery, the yard cannot close its own records for the flag.
Where is the list of items and testing standards?
The directive itself does not list equipment. The Commission does that in an implementing regulation, which is replaced at regular intervals as the IMO instruments and testing standards change. At the time of writing the one in force is Commission Implementing Regulation (EU) 2026/1434, which repealed Implementing Regulation (EU) 2025/1533. That in turn had repealed (EU) 2024/1975.
The annex is a table. Each row is an item with a MED number. The columns are worth knowing by name, because they are what you check an enquiry against.
| Column | What it tells the maker |
|---|---|
| Number and item designation | Whether your product is a listed item, and under which number |
| SOLAS regulations and the relevant IMO resolutions and circulars | The requirement the item has to meet |
| Testing standards | The standards the item is tested to for this entry |
| Modules for conformity assessment | Which modules are allowed for this item |
| First placing on the market | The date from which the entry applies |
| Last placing on board | The date after which equipment approved to an older entry may no longer be placed on board |
The two date columns matter to a maker with stock or a long delivery. When an entry is replaced by a newer one, the older approval has an end date for placing on board. A certificate that was right when you quoted can be out of date by the time the ship is fitted out. Each regulation also carries transitional provisions for items newly added to the list.
What is the MarED database, and where is it now?
The directive requires the Commission to keep a database of certificates, declarations and related information. For years the product database was known as MarED. The MarED web address now redirects to the MED Portal run by the European Maritime Safety Agency, EMSA.
- EMSA describes the portal as holding the approved marine equipment that may be carried on ships flagged in EU member states, Iceland and Norway.
- Users can check whether a certificate for an item of marine equipment is valid. There is a mobile version.
- Yards, owners and inspectors use it. Look your own product up before you state in an offer that it is wheel-marked.
What happens in exceptional cases?
The directive has a few narrow routes for equipment without a wheel mark. They are decisions for the flag state, not for the maker or the yard, and none of them is a general alternative to approval.
- Technical innovation. A flag state may permit equipment that has not been through the normal procedures if trials or other evidence satisfy it. The equipment then carries a certificate from that state.
- Replacement outside the EU. Where equipment must be replaced in a port outside the Union and wheel-marked equipment cannot reasonably be obtained, other equipment may be fitted with documentation, under conditions the directive sets.
- Transfer of flag. When a ship moves to an EU flag, its equipment must carry the wheel mark or be accepted as equivalent by that member state's administration.
The UK position: the Merchant Shipping (Marine Equipment) Regulations
The UK has its own regime for equipment on UK ships. The Merchant Shipping (Marine Equipment) Regulations 2025, S.I. 2025/1280, replaced the 2016 regulations of the same name and the 2019 amendments to them. Published guidance from an approved body gives 5 January 2026 as the date they entered into force. The regime is often shortened to MER.
- Approval is given by a UK approved body designated by the Maritime and Coastguard Agency, the MCA.
- The manufacturer draws up a UK declaration of conformity and affixes the UK conformity mark. The wheel mark is the EU's mark, not the UK's.
- The technical detail sits in Merchant Shipping Notice MSN 1874 (M+F), which lists the equipment and standards and names the approved bodies. It is amended regularly. Amendment 12 was published on 15 October 2026.
- MSN 1874 also has an annex for certain equipment approved by the United States Coast Guard, under a mutual recognition agreement between the UK and the US.
- The regulations include a provision on equivalents. The government's consultation described a written acceptance by the MCA for cases where UK-approved equipment is not available or not technically compatible.
- The 2025 regulations brought the approval of ballast water management systems into the same framework.
Do not assume that a wheel-marked product may go on a UK ship, or that a UK-marked product may go on an EU ship. For a UK-flagged newbuild, read the current MSN 1874 on gov.uk and ask a UK approved body. Several organisations act as both an EU notified body and a UK approved body, but the two approvals are separate.
Where does OdysseyGPT fit?
OdysseyGPT reads documents. Document Review compares a yard's enquiry with your offer documents, including any module certificates and declarations you upload, and quotes both sides for each finding. It does not decide whether an item is in scope of the directive, does not look anything up in the MED Portal and issues no declaration or mark. Those remain with the manufacturer, the notified body and the flag state.
What to check in a tender against the MED
| Check | Why it matters |
|---|---|
| The flag the ship will fly at delivery | An EU flag brings the directive in. A UK flag brings in the UK regulations. Another flag has its own rules |
| Whether your product is a listed item in the implementing regulation in force, and its MED number | If it is not listed, the wheel mark does not apply and must not be affixed |
| The row your certificate was issued against, and its last placing on board date | An approval to a superseded entry has an end date that may fall before the ship is fitted out |
| The modules you hold: B with D, E or F, or G | The yard may ask for the certificates by module, and both parts of a pair must be valid |
| The expiry dates of the module certificates against the delivery date | A lapsed quality system approval stops you marking products |
| The exact model, size and variants on the type-examination certificate against what is offered | Variants outside the certificate are not covered |
| Whether the yard also asks for class type approval for the same item | It is a separate certificate. See class type approval |
| The EU declaration of conformity: who issues it, in which languages, and how many copies go with the goods | A copy has to stay on board with the equipment |
| Marking on the product: the wheel mark, the notified body number and the year | A missing or incomplete mark is found at survey |
| Whether the yard asks you to confirm the listing in the MED Portal | Check your own entry first, so the offer and the portal agree |
| For a UK ship: UK approval, the UK conformity mark and the UK declaration | The wheel mark alone should not be assumed to be enough |
| For a series of ships: whether a new implementing regulation could apply to later hulls | The list is replaced regularly and later ships may fall under newer entries |
The wider enquiry process, with class requirements and the documents due after award, is on the marine equipment manufacturers page. A layout for the certificate set is on the class certificate checklist template page.
Talk through your tender review
See how OdysseyGPT reviews a tender
Tell us how your team reviews tenders today. We can walk through an example together.
