OdysseyGPT

Standards explainer

ISO 5208 valve pressure testing: shell and seat tests, lettered leakage rates and what to check in a tender

An overview of ISO 5208 for bid, quality and test engineers at valve makers, with its relation to API 598 and EN 12266 and a checklist for the test clauses in an enquiry.

By Ademola Afolabi, Founder, New Odyssey Ltd · Last reviewed:

The short answer

ISO 5208 is the international standard for pressure testing metallic industrial valves. It sets the examinations and tests a manufacturer uses to prove the pressure boundary is sound and the closure is tight: a shell test and a seat (closure) test. Allowable seat leakage is given as lettered rates, chosen by the product standard or the purchaser.

Key Takeaways

  • ISO 5208 is a test standard for metallic valves. It is applied together with a valve product standard.
  • Where the product standard and ISO 5208 differ, the product standard governs.
  • Seat leakage is specified by a lettered rate. Rate A means no visible leakage during the test.
  • A tender must name the rate. "Tested to ISO 5208" alone does not say how tight the valve must be.

Free sample: an ITP and FAT readiness check. Send your ITP and the customer's quality specification. Get a readiness check before the inspector arrives. Get the free result

What is ISO 5208?

ISO 5208 is titled Industrial valves — Pressure testing of metallic valves. ISO's abstract says it specifies the examinations and tests a valve manufacturer needs to carry out to establish the integrity of the pressure boundary of a metallic industrial valve, and to verify how tight the closure is and whether the closure mechanism is structurally adequate.

It is not meant to stand alone. The abstract says it is intended to be applied with the specific requirements of a valve product standard, to the extent that the product standard cites it. Where the two differ, the product standard's requirements apply. The standard does not deal with the safety aspects of pressure testing; those stay with the test shop.

The current edition is the fourth, published in 2015. ISO reviewed and confirmed it in 2025. Older orders may still name the 2008 edition, which has been withdrawn, or an earlier one, and the leakage rate table has changed over the editions. Test to the edition the contract names.

The tests ISO 5208 sets

ISO 5208 tests at concept level (own summary; pressures and durations are in the standard)
TestWhat it provesWhat a tender tends to change
Shell testThe body, bonnet and their joints hold pressure with no visible leakage through the pressure boundaryTest fluid, water quality and a longer hold time
Backseat testThe stem backseat seals, on valves that have this featureWhether it is required at all, and its record
Closure (seat) testThe obturator seals against the seat within the leakage rate specifiedLiquid or gas, test direction, both seats or one, and the rate letter

The standard allows the closure test to be made with a liquid or with a gas, and the allowable leakage is stated differently for each. A low-pressure gas test and a high-pressure liquid test show different things about a seat. If the enquiry asks for both, each one is a line in the test procedure and in the price.

Duration and pressure depend on valve size and rating, and the tables for them are in the standard. Do not take them from a summary, including this one.

Leakage rates as lettered categories

ISO 5208 does not give one pass mark for seat leakage. It gives a series of rates named by letter, running from Rate A through to Rate G. The 2015 edition also has intermediate rates with doubled letters. Rate A is the tightest: no visually detectable leakage for the duration of the test. Each later rate allows more leakage, and the allowance grows with the nominal size of the valve.

  • The rate is chosen by the valve product standard, or by the purchaser where the product standard leaves it open.
  • Soft-seated valves are commonly ordered to Rate A. Metal-seated valves are commonly ordered to one of the later rates.
  • A rate letter is tied to its edition. The same letter in an older edition, or in another standard, may allow a different amount.
  • The test fluid matters. A rate met with liquid is not evidence that the valve meets the same letter with gas.

"Zero leakage" is not a rate

Tenders sometimes ask for zero leakage or bubble-tight shut-off without naming a rate. Ask the customer to state the ISO 5208 rate, the test fluid and the test pressure. Then check that your seat design is offered to that rate, and record any difference as a deviation.

ISO 5208, API 598 and EN 12266

Three valve pressure test standards side by side (own summary)
StandardWhere you meet itHow seat leakage is specified
ISO 5208ISO valve product standards and many international project specificationsA lettered rate, chosen by the product standard or purchaser
API 598Valves built to API product standards such as API 600 and API 602No visible leakage for resilient seats; an allowance by valve size for metal seats
EN 12266-1 and EN 12266-2Valves to European product standards, often with the Pressure Equipment DirectiveLettered rates in Part 1, which holds the mandatory tests; Part 2 holds supplementary tests

EN 12266-1 was drawn up on the basis of an earlier edition of ISO 5208, so the two look alike. They are separate documents with their own editions, and EN 12266-1 labels its tests with codes for shell strength, shell tightness and seat tightness. Do not assume that a letter in one standard equals the same letter in the other. Compare the tables in the editions named.

A valve built to API 6D is tested to API 6D's own clauses, which refer to ISO 5208 rates for seat leakage. An enquiry that names API 598 on the datasheet and an ISO 5208 rate in the project specification is asking for two acceptance bases. Raise it before you quote.

What to check in a tender against ISO 5208

Valve test clauses to settle before the offer goes out
CheckWhy it matters
Edition of ISO 5208 named, and the product standard that calls it upThe product standard governs where they differ
Leakage rate letter for each valve type and seat type in the enquiryNo letter means no acceptance criterion
Closure test fluid: liquid, gas or bothAllowances differ by fluid, and a gas test needs its own set-up
Seats and directions to be testedBidirectional valves and double-seated valves take more test steps
Any second test standard named elsewhere in the packageAPI 598, EN 12266-1 or an owner standard may conflict with the rate
Hold times or pressures above the standard's minimumsThey change test bay throughput on a large order
Water quality limits and drying after testChloride limits apply to stainless steels in many owner standards
Who attends: customer, third party or manufacturer onlyAttendance points go into the inspection and test plan
Form of the test certificate and what it must stateRate, fluid, pressure, duration and gauge identity are usual requests
Calibration evidence for gauges and recordersCertificates must be valid on the test date

OdysseyGPT's Document Review reads the enquiry package and your standard test procedure together, and reports where the customer's test clauses ask for more than you offer, quoting both documents. For the records after testing, the Calibration Validity Check (beta) matches each gauge named on a test report to its certificate. OdysseyGPT does not test valves or issue test certificates. For a certificate layout, see the valve test certificate checklist.

Try it on your own documents

Free sample: an ITP and FAT readiness check

Send your ITP and the customer's quality specification. Get a readiness check before the inspector arrives.

Get the free result

Frequently asked questions

What is ISO 5208?

The international standard for pressure testing metallic industrial valves. It sets a shell test, a backseat test where the valve has one, and a closure test, and it gives allowable seat leakage as lettered rates.

What does ISO 5208 Rate A mean?

No visually detectable leakage for the duration of the test. It is the tightest rate in the standard and is commonly specified for soft-seated valves.

Is ISO 5208 the same as EN 12266-1?

No. EN 12266-1 was based on an earlier edition of ISO 5208 and is similar, but it is a separate European standard with its own editions and test codes. Check the tables in the editions your contract names.

What is the difference between ISO 5208 and API 598?

Both cover valve pressure testing. ISO 5208 gives a range of lettered leakage rates and leaves the choice to the product standard or purchaser. API 598 gives no visible leakage for resilient seats and a size-based allowance for metal seats.

Who decides the ISO 5208 leakage rate?

The valve product standard, or the purchaser where the product standard leaves it open. If the enquiry does not name a rate, ask for one before quoting.

References

ISO 5208:2015 Industrial valves — Pressure testing of metallic valves

ISO

Public abstract and status. The standard is a paid document.

Visit source

BS ISO 5208:2015 catalogue entry

BSI

Visit source

EN 12266-1:2012 Industrial valves — Testing of metallic valves — Part 1

CEN (catalogue entry)

Paid standard. Scope and test names only.

Visit source

What is ISO 5208?

Projectmaterials

Visit source

API Standard 598: Valve Inspection and Testing

American Petroleum Institute

Paid standard.

Related Pages