OdysseyGPT

Glossary term

Safe Working Load (SWL)

The maximum load that a piece of lifting equipment may lift in a given configuration, as marked on the equipment for the user.

Last reviewed by the OdysseyGPT team

What it is

The safe working load, or SWL, is the maximum load a piece of lifting equipment may lift in a given configuration. LOLER in Great Britain requires it to be marked on the equipment. It starts from the manufacturer's rating. Crane standards say rated capacity, and accessory standards often say working load limit.

Key Takeaways

  • LOLER requires lifting equipment to be marked with its safe working load.
  • Where the load depends on configuration, each configuration needs to be covered.
  • Rated capacity, maximum working load and working load limit are related terms from other documents.
  • The figure should be identical on the plate, the declaration, the certificate and the instructions.

Why it matters

Safe working load, shortened to SWL, is the load that lifting equipment must not exceed in normal use. In Great Britain the term has legal weight. HSE's guidance on LOLER says lifting equipment must be marked with its safe working load. Where the load depends on the configuration, as with a crane whose capacity changes with radius, the information must cover each configuration. Accessories must be marked with whatever is needed for their safe use. The safe working load is also one of the items the report of a thorough examination must state. The value is not chosen freely by the user. It starts from the manufacturer's rating, which comes out of the design calculation and the tests. A user or competent person may set a lower figure for a particular installation or after a defect is found. Other documents use other words for nearly the same idea. Crane standards usually speak of rated capacity. The EU Machinery Directive speaks of the maximum working load and requires it to be marked on lifting machinery. Standards for lifting accessories often use working load limit. These terms are defined in their own documents and are not always interchangeable, so it is safer to repeat the term the governing document uses than to translate it. For a manufacturer, the practical points are consistency and scope. The load on the data plate, in the declaration of conformity, on the test certificate and in the instructions should be the same number, stated for the same configuration. The offer should also make clear whether a lifting beam or other attachment below the hook counts against the capacity.

How OdysseyGPT uses it

OdysseyGPT does not calculate or assign a safe working load. It compares what documents say. Document Review can set the capacity in the customer's specification beside the capacity in your technical specification, and quote both where they differ or where one is silent on the configuration. Checking that the plate on the equipment matches the paperwork is a physical inspection, which the software does not do.

Evaluation questions

Where is the safe working load marked?

On the equipment itself, where the operator can see it. Where the load varies with configuration, the information for each configuration is kept with the equipment, for example through a rated capacity indicator.

Does the thorough examination report state the safe working load?

Yes. Schedule 1 of LOLER lists the safe working load, or the load for the last configuration examined, among the contents of the report.

Can OdysseyGPT check the safe working load?

It can compare the figure stated in one document with the figure in another and quote both. It does not calculate the load or inspect the marking.

Frequently asked questions

What is a safe working load?

The maximum load a piece of lifting equipment may lift in a given configuration. Under LOLER in Great Britain, lifting equipment must be marked with it.

Is safe working load the same as working load limit?

They are close in meaning but come from different documents. Working load limit is common in standards for lifting accessories. Safe working load is the term in LOLER. Use the term the governing document uses.

Who sets the safe working load?

It starts from the manufacturer's rating, based on the design and tests. A user or competent person can reduce it for a particular installation or condition. They should not increase it.

Does the safe working load include a lifting beam below the hook?

Normally the weight of a beam or other attachment hanging from the hook counts as part of the load the crane lifts. Check how the maker states the capacity. The attachment has its own marked load as well.

References

Lifting Operations and Lifting Equipment Regulations 1998 (LOLER): overview

Health and Safety Executive

Marking of lifting equipment and accessories with the safe working load. Read 15 Nov 2026.

Visit source

The Lifting Operations and Lifting Equipment Regulations 1998 (SI 1998/2307)

legislation.gov.uk

Schedule 1: the safe working load in the examination report.

Visit source

Directive 2006/42/EC on machinery

EUR-Lex

Annex I, part 4: marking of lifting machinery with the maximum working load.

Visit source

Related Pages