OdysseyGPT

Glossary term

Mechanical Run Test

A shop test in which an assembled pump, compressor or other rotating machine is run at speed for a set period while vibration, bearing temperatures and other mechanical readings are recorded.

Last reviewed by the OdysseyGPT team

What it is

A mechanical run test is a shop test of an assembled rotating machine, such as a pump or compressor. The machine is run at speed for a set period while vibration, bearing temperatures and other mechanical readings are recorded against agreed limits. It proves mechanical soundness and is separate from the performance test.

Key Takeaways

  • It checks mechanical behaviour: vibration, temperatures, leakage.
  • It is separate from the performance test, though both may be run together.
  • Whether it is required, and for how long, comes from the standard and the purchase order.
  • Witness level and notice period belong in the inspection and test plan.

Why it matters

A mechanical run test, called a mechanical running test in the compressor standards, shows that a rotating machine is mechanically sound before it leaves the works. The machine is assembled, coupled to a shop or contract driver and run at its operating speed for a period set by the standard or the purchase order. During the run the test engineer records shaft or bearing housing vibration, bearing and lubricating oil temperatures, speed and any leakage, and checks them against the limits agreed in the order. The test says nothing direct about hydraulic or aerodynamic performance; that is the job of the performance test. How the test is specified depends on the machine. For compressors built to API 617, a mechanical running test is described as part of the standard test scope for every machine. For centrifugal pumps to API 610, mechanical readings are taken during the performance test, and a separate, longer mechanical run is an optional test that the purchaser specifies. The purchase order also says whether the test is witnessed, which parts must be the contract parts, and whether bearings are opened for inspection afterwards.

How OdysseyGPT uses it

OdysseyGPT does not run, monitor or witness tests and does not read vibration data. It checks the documents around the test. Document Review finds the test requirements in the customer's specification and compares them with your standard test procedure before you quote. FAT Readiness Check (beta) checks before the test day that the procedure is approved, the instruments named are in calibration and the witness notice meets the stated period. Findings quote their source, and engineers decide.

Evaluation questions

What should a bid engineer check about the mechanical run test in a tender?

Whether it is required, its duration, whether it is witnessed, which contract parts must be fitted, any inspection after the run, and vibration or temperature limits tighter than the standard. Each can change test bay time and cost.

What goes in a mechanical run test record?

The machine's identity, the test date, the procedure revision, the readings at each interval, the instruments used with their calibration status, the result and the signatures of the test engineer and any witness.

Does OdysseyGPT analyse vibration data from a run test?

No. It reads documents such as specifications, procedures, test reports and calibration certificates, and reports gaps between them with a quote for each. It does not acquire or interpret machine data.

Frequently asked questions

What is a mechanical run test?

A shop test in which the assembled machine is run at speed for a set time while vibration, bearing temperatures and similar readings are recorded and compared with agreed limits.

What is the difference between a mechanical run test and a performance test?

The mechanical run test shows the machine runs smoothly and its bearings and seals behave. The performance test shows it delivers the guaranteed flow, head or pressure, and power. They can be run in one session or separately.

Is a mechanical run test mandatory?

It depends on the standard and the order. For API 617 compressors it is described as a test on every machine. For API 610 pumps a separate mechanical run is optional and applies when the purchaser specifies it.

What is recorded during a mechanical run test?

Typically speed, vibration, bearing and oil temperatures, oil pressures and flows, any seal leakage, and the identity of the instruments used. The test procedure lists the readings and the acceptance limits.

References

Centrifugal compressors shop tests

Turbomachinery International

Visit source

Performance testing centrifugal pumps

Pumps & Systems

Visit source

API Standard 617 and API Standard 610

American Petroleum Institute

Paid standards. Use the edition your contract names.

Related Pages