What does API 6A cover?
API Specification 6A, Wellhead and Tree Equipment, sets requirements for the equipment at the top of a well: the wellhead that supports the casing and tubing, and the tree of valves and fittings above it that controls flow. Public scope descriptions list wellhead equipment, connectors and fittings, casing and tubing hangers, valves and chokes, and loose connectors. The specification covers design, materials, quality control, testing and marking of new equipment.
The 21st edition is dated 2018, and API's Monogram Program has applied it since 1 November 2019. API has issued addenda and errata since then, so check which ones your contract includes. ISO 10423:2022 is written as a supplement to that edition. Repair and remanufacture are handled in a separate API document, and tools for installation and servicing are outside the scope.
API 6A is not a general valve standard. A valve on a tree is bought to API 6A. A valve on the flowline or in the process piping downstream is usually bought to API 6D or another product standard. The API valve standards hub compares them.
The five designations a purchaser specifies
API 6A describes service conditions in terms of pressure, temperature and material class, and then adds two levels that set how much proof the purchaser gets. A requisition or datasheet for API 6A equipment should state all five. If one is missing, ask.
| Designation | What it tells the manufacturer | What to look for |
|---|---|---|
| Rated working pressure | The maximum internal pressure the equipment is designed for. API 6A uses its own set of ratings, published as running from 2,000 to 20,000 psi, and not ASME pressure classes | One rating for the whole assembly, or different ratings above and below a crossover |
| Temperature class | A letter code that stands for a minimum and maximum temperature range | Whether the minimum reflects the lowest ambient temperature at site, not only the flowing temperature |
| Material class | A two-letter code that says how corrosive the retained fluid is and so which families of material may be used for bodies, bonnets and internal parts | Whether the class is one of the sour service classes |
| Product specification level (PSL) | How much quality control the product receives: material testing, non-destructive examination, traceability and the testing of the finished item rise with the level | Whether the level is at or above the minimum the specification sets, and whether gas testing is asked for |
| Performance requirement (PR) | The level of design validation behind the product, with PR2 asking for more extensive validation testing than PR1 | Whether your design has validation records for the level, size and rating ordered |
PSL deserves care. Earlier editions left the level largely to the purchaser. API's announcement for the 21st edition says a minimum PSL now applies, set by the pressure rating and the material class, and that the quality requirements were regrouped by activity. The specification also has an informative annex to help a purchaser choose a level. An offer at a lower PSL than the requisition asks for is a deviation, even where the specification's own minimum would allow it.
API 6A and NACE MR0175 for sour service
API 6A does not write its own sour service rules. For the material classes intended for sour service, it requires the materials to meet NACE MR0175 / ISO 15156. The marking for those classes also carries the maximum H2S partial pressure the equipment is suitable for, so two items of the same sour class can have different limits.
For a bidder this means two checks, not one. The material class on the datasheet has to match what you offer, and the H2S limit behind it has to cover the service conditions the purchaser gives. Check the units used for that limit in the edition named. If the requisition gives a material class and no H2S partial pressure, or the two do not agree, raise a clarification. The sour service material checklist template lists the points to settle.
What does the API Monogram add?
Building to API 6A and marking with the API Monogram are different things. The Monogram Program is a voluntary licence from API. A licensed manufacturer runs a quality management system to API Spec Q1, is audited by API, and may apply the mark with its licence number to new products that meet the specification and were made at the licensed facility.
A purchaser who wants monogrammed equipment has to say so in the order. A manufacturer without a licence can state that a product is designed and made to API 6A, but cannot apply the mark. If the requisition asks for the monogram, check that your licence covers API 6A, the facility where the item will be made, and the product type ordered.
What to check in a requisition against API 6A
| Check | Why it matters |
|---|---|
| Edition of API 6A named, and whether addenda and errata are included | Requirements changed between editions, including how PSL is set |
| Whether ISO 10423 is named as well, or in place of API 6A | The two are related documents and are not identical |
| Rated working pressure for each item and at each end connection | Crossovers join two ratings, and the designations follow rules for that case |
| Temperature class against the site's minimum ambient and maximum flowing temperature | A class chosen for flowing conditions can miss a cold start |
| Material class, and the H2S partial pressure limit where the class is a sour one | The limit is part of the designation and of the marking |
| Any material requirement beyond the class: named alloys, hardness limits, cladding or overlay | Owner specifications often add to the class |
| PSL for each item, against the specification's minimum and your standard build | A higher level changes material testing, examination and records |
| Whether gas testing is required | It needs test facilities and time that a hydrostatic-only build does not |
| PR level, and whether design validation records are to be submitted | Validation is done on a design, in advance. It cannot be added to an order late |
| End and outlet connections: type, size and ring gasket | Mismatches here are found at site, at the worst moment |
| API Monogram required or not | Only a licensee can apply it, and only at the licensed facility |
| Inspection, witness and hold points, and third-party inspection | Notice periods set the delivery date |
| Records to be supplied and how long they are kept | They go into the record book and the retention period may exceed your own |
| Bolting requirements | API's announcement for the 21st edition says bolting must meet a minimum level of API 20E or 20F |
OdysseyGPT's Document Review reads a requisition's specifications against your own product specification or datasheet and drafts the compliance matrix and deviation list, with each row quoting both sides. Datasheet Comparison (beta) sets the purchaser's datasheet beside yours field by field, which is where a different PSL or material class shows up. It reports what the documents say. It does not select a material class, check a design against API 6A, or confirm that a monogram licence is valid.
Use the standard, not a summary
This page explains the ideas so you can read a requisition. It does not replace the specification. The ratings, classes, test requirements and marking rules are in API 6A itself, in the edition and addenda your contract names.
Talk through your tender review
See how OdysseyGPT reviews a tender
Tell us how your team reviews tenders today. We can walk through an example together.
