OdysseyGPT

Free template

Sour service material checklist: checking materials and certificates on a NACE MR0175 order (Excel and CSV)

For package builders, valve makers and fabricators: one row per pressure-containing or wetted part, with the order's sour service wording beside what the certificate shows.

By Ademola Afolabi, Founder, New Odyssey Ltd · Last reviewed:

The short answer

A sour service material checklist compares each part's material certificate with what the order requires for sour service. This free Excel template has one row per pressure-containing or wetted part: material, the customer's sour service clause, the hardness requirement and heat treatment condition as the order states them, the certificate type required and what the certificate shows.

Key Takeaways

  • The checklist holds the order's wording, such as "hardness per PO clause 6.3". It gives no hardness limit.
  • List every wetted part, including bolting, welds, valves and instruments.
  • A supplier's statement of compliance should name the edition of the standard, and the order may still ask for the certificates behind it.
  • The example has 10 parts for an invented separator skid order (PO-EX-7390), with three fails and three queries.

Download the sour service material checklist

Both files are free under CC BY 4.0, with no form to fill in. The XLSX opens in Excel, Google Sheets, LibreOffice and Numbers. The CSV carries the table only; the header block is in the XLSX.

Where sour service orders go wrong on paper

When a purchase order calls up NACE MR0175/ISO 15156, the requirement reaches every part that holds pressure or touches the fluid, and each part's certificate has to show it was met. The purchaser states the service conditions; the standard and the order then decide which materials, conditions and hardness controls apply. The problems tend to be small and late: a certificate of the wrong type, bolting in a similar grade, a forging tested once per heat when the order wanted every piece. This checklist puts those points in one table at goods-in, while a part can still be replaced.

  • Quality engineers at package builders and fabricators, at goods-in and again before the record book closes.
  • Materials and welding engineers, who answer the queries.
  • Buyers, who can copy the requirement columns into the purchase order for each sub-supplier.

The checklist does not judge whether a material suits the service. That is an engineering decision, made against the standard at the edition the order names and the conditions the purchaser gives. Check the governing standard or contract. To go through a single certificate line by line, use the MTR review checklist template with how to review a material test report. See also oil and gas package builders.

Header block

Header block fields, with the invented example values
FieldExample
ProjectExample Gas Gathering Station (fictional)
CustomerExample Energy Company Ltd (fictional)
Purchase orderPO-EX-7390 (fictional)
EquipmentInlet filter separator skid: vessel V-7390, pipework and valves (fictional)
Sour service requirementPO clause 6 and specification MS-EX-SS-01 Rev 2 (invented)
Standard and edition named in the orderNACE MR0175/ISO 15156, at the edition the PO states
Service conditionsAs the customer's process datasheet PD-EX-7390 Rev B states them
Checklist no.SSC-EX-7390
Date2027-06-08
Prepared byQuality engineer
Checked byMaterials engineer

Example rows: an inlet filter separator skid

Invented example rows for order PO-EX-7390
ItemPartMaterialSour service requirementHardness requirement as stated in the orderHeat treatment requiredCertificate requiredWhat the certificate showsStatusRemark
1Vessel shell plateSA-516 Grade 70PO clause 6.1; MS-EX-SS-01 4.2Hardness per PO clause 6.3Normalised, as MS-EX-SS-01 4.2EN 10204 3.1Heat EX-H-4471: normalised; hardness reported and inside the PO clause 6.3 limit; type 3.1OK
2Vessel headsSA-516 Grade 70PO clause 6.1; MS-EX-SS-01 4.2Hardness per PO clause 6.3Normalised; heat treated after forming as MS-EX-SS-01 4.3EN 10204 3.1Heat EX-H-4480: plate certificate normalised; no record of heat treatment after formingQueryAsk the head maker for the heat treatment record after forming and the hardness taken afterwards.
3Nozzle forgingsSA-105PO clause 6.1; MS-EX-SS-01 4.4Hardness per PO clause 6.3; each forging tested, as MS-EX-SS-01 4.4Normalised, as MS-EX-SS-01 4.4EN 10204 3.1Heat EX-H-5102: normalised; hardness reported for one sample per heatFailThe order asks for a hardness test on each forging. Test the remaining forgings or ask the customer for a concession.
4Nozzle pipeSA-106 Grade BPO clause 6.1; MS-EX-SS-01 4.2Hardness per PO clause 6.3As MS-EX-SS-01 4.2EN 10204 3.1Heat EX-H-5230: condition and hardness reported as the order asks; type 3.1OK
5FlangesSA-105PO clause 6.1; MS-EX-SS-01 4.4Hardness per PO clause 6.3Normalised, as MS-EX-SS-01 4.4EN 10204 3.1Heat EX-H-5117: certificate received is type 2.2FailWrong certificate type. Ask the stockist for the mill's 3.1 certificate for this heat.
6Pressure boltingSA-193 B7M studs; SA-194 2HM nutsPO clause 6.2; MS-EX-SS-01 5.1Hardness per PO clause 6.3; grade as MS-EX-SS-01 5.1As the bolting specification requires for the grade orderedEN 10204 3.1Lot EX-L-0933: certificate shows grade B7 studs, not B7MFailGrade supplied is not the grade ordered. Quarantine the lot and reorder.
7Pressure weldsWPS-EX-12, qualified by PQR-EX-12PO clause 6.4; MS-EX-SS-01 6.1Hardness survey on the procedure qualification per PO clause 6.4Post-weld heat treatment as MS-EX-SS-01 6.2PQR with hardness surveyPQR-EX-12 includes a hardness survey and the post-weld heat treatment recordOKProduction PWHT chart still to be filed in the record book.
8Ball valve bodies and trimAs valve datasheet DS-EX-V-02PO clause 6.5; MS-EX-SS-01 7.1Hardness per PO clause 6.3As the valve datasheet statesEN 10204 3.1 for body, ball and stemValve maker's statement of compliance only; no material certificates for ball and stemQueryAsk the valve maker for the certificates of the ball and stem.
9Level gauge wetted partsAs instrument datasheet DS-EX-LG-01PO clause 6.5; MS-EX-SS-01 7.2As the supplier's statement of compliance declaresNot stated in the orderSupplier's statement naming the standard and its editionStatement names the standard without an editionQueryAsk for a statement that names the edition the PO states.
10Filter element support and internalsAs drawing V-7390-04PO clause 6.1; MS-EX-SS-01 4.6Hardness per PO clause 6.3As MS-EX-SS-01 4.6EN 10204 3.1Not receivedCertificates due from the internals supplier before assembly.

The hardness column repeats the invented order's own wording, "hardness per PO clause 6.3", and never a number. Nothing in the example is presented as a requirement of NACE MR0175/ISO 15156: the grades, heat treatment conditions and certificate types are what an invented purchase order and specification (MS-EX-SS-01) ask for. Every example value is invented: the project, customer, bidders, purchase order, prices and every document, certificate, serial and report number do not exist. Standards are named but not quoted.

Status values

StatusUse it when
OKThe certificate shows what the order asks for: material, heat treatment condition, hardness as the order states it, and the certificate type.
QuerySomething is missing or unclear on the certificate. Ask the supplier before the material is released.
FailThe certificate shows something different from the order. Hold the material and raise a nonconformance.
Not receivedNo certificate yet. The part cannot be released on a promise.

Columns and what to write

ColumnWhat to write
ItemRunning number.
PartOne pressure-containing or wetted part per row, as the bill of materials names it. Include bought-in items and welds.
Material specification and gradeThe specification and grade on your bill of materials and on the order.
Customer's sour service requirementThe PO clause, specification clause or datasheet note that sets the sour service requirement for this part.
Hardness requirement as stated in the orderThe order's own wording and clause, for example "hardness per PO clause 6.3". Copy any figure from the order, not from memory of the standard.
Heat treatment condition requiredThe condition the order or the specification requires for this part, with the clause.
Certificate type requiredThe certificate or document the order asks for, such as an EN 10204 type, a procedure qualification record or a supplier's statement.
What the certificate showsWhat the document received actually says: heat number, condition, hardness reported and how often it was tested, and the certificate type.
StatusOK, Query, Fail or Not received (drop-down). Fail rows turn red; Query and Not received rows amber.
RemarkWhat is wrong or missing, and the action before the material is used.

How to work through an order

  1. Fill in the header block: the order, the customer's sour service clauses and specification, the standard and edition the order names, and where the service conditions are stated.
  2. From the bill of materials, list every pressure-containing and wetted part, one row each. Include bolting, welds, valves and instruments; bought-in items are the ones most often missed.
  3. For each part, write the material specification and grade and the clause that sets the sour service requirement.
  4. Copy the hardness requirement and the heat treatment condition from the order, in the order's own words. Whether a material is acceptable for the service is decided by the standard and the conditions the purchaser states, not by this list.
  5. Write the certificate type the order asks for, then lay each certificate beside its row and record what it shows: heat number, condition, hardness reported and how often it was tested.
  6. Set the status. Fail rows turn red; Query and Not received rows amber.
  7. Hold material on any Fail, Query or Not received row until the remark is answered. A concession needs the customer's written agreement.
  8. File the finished checklist with the certificates in the record book.

Checking a stack of certificates against the order

A skid can carry a hundred certificates, and the sour service clause applies to most of them. In OdysseyGPT's Manufacturing QA module, Material Certificate Review (beta) reads each certificate and the purchase order and reports where grade, condition, reported hardness or certificate type differs from what the order asks, with the page it found it on. It compares documents. It does not decide whether a material is acceptable for the service; your materials engineer does. Tools marked beta are open on request, and we onboard each team ourselves.

Want us to run the check for you?

Send up to 20 material certificates and the purchase order. We send back a certificate check report, each finding cited to its page.

Get the free certificate check

New templates by email (optional)

Your download does not depend on this.

We use your email only for this. See our privacy policy.

Frequently asked questions

What is sour service?

Service in which the fluid contains hydrogen sulphide under conditions that can crack susceptible metals. The purchaser decides whether a duty is sour and states the conditions, and the equipment supplier works to them.

What does NACE MR0175/ISO 15156 ask of materials?

It sets out which materials may be used in oil and gas production environments containing hydrogen sulphide, and under what conditions, with controls on hardness and heat treatment for many of them. The detail depends on the material, the environment and the edition, so read the standard itself. Check the governing standard or contract.

Why does the checklist give no hardness limit?

Limits differ by material type, product form and edition, and many orders add their own. The right figure is the one your order and the standard it names give for that part, so the template has you copy it from there.

Is a supplier's statement of compliance enough?

Only if the order says so. Many orders also want the material certificates that support the statement, and a statement that names no edition is hard to rely on. The example treats both cases as queries.

Can I use it with a product standard such as API 6A?

Yes. A product standard may add its own material and documentation rules for sour service. Add columns or rows for them, and take the requirements from the order and the edition it names.

References

Creative Commons Attribution 4.0 International

Creative Commons

Visit source

Related Pages